diploma in comp sci i vi cu

7/28/2019 Diploma in Comp Sci I VI CU

1/52

INDIRA GANDHI NATIONAL OPEN UNIVERSITYSCHOOL OF ENGINEERING AND TECHNOLOGYMAIDAN GARHI, NEW DELHI-110 068

Programme Structure ofVertically Integrated Engineering programmes

Level of Programme : DiplomaDiscipline : Computer Science & Engineering

PROGRAMME CODE : DCSVI

First Semester

Sl.No.

CourseCode

Course Description CreditLoad per

WeekRemarks

1. BET-011 Mathematics-I 4 4

2. BET-012 Physics 4 4

3. BET-013 Chemistry 4 4

4. OIEL-001 Technical English 4 4

5. BET-014 Applied Mechanics 4 4

6. BETL-011 Lab-I (Applied Science) 1 2

7. BETL-012 Lab-II (Applied Mechanics) 1 2

TOTAL 22 24

Second Semester

Sl.No.

CourseCode


WeekRemarks

1. OIEE-001 Basics Of Electrical Engineering 4 4

2. BET-016 Engineering Drawing 4 4

3. BET-026 Workshop Technology 4 4

4. BET-024 E/M Engineering 4 4

5. OICS-001 Data Structures & Files 4 4

6. BETL-022 Lab-III (Workshop Technology) 1 2

7. OIEEL-001 Lab-IV (Electrical Engineering) 1 2

TOTAL 22 24


2/52

Third Semester

Sl.No.

CourseCode


WeekRemarks

1. BET-021 Mathematics-II 4 4

2. BET-017 Computer Basics 4 4

3. BET-022 Strength of Materials 4 4

4. BICS-027 Computer Organisation 4 4

5. BIEL-027 Applied Electronics 4 4

6. BICEL-016 Lab-V (Computer Application) 1 2

7. BMEL-008 Lab-VI (Strength of Materials) 1 2

TOTAL 22 24

FourthSemester

Sl.No.

CourseCode


WeekRemarks

1. BICS-028 PC Assembly and Maintenance 4 4

2. BICS-029 Algorithms and Logic Design 4 4

3. BICS-030 C Programming 4 4

4. BICS-031 Basics of Networking 4 4

5. BIEE-032 Principles of Computer Architecture 4 4

6. BICSL-015 Lab-VII(PC Assembly Lab) 1 2

7. BICSL-016 Lab-VIII(C Programming Lab) 1 2

TOTAL 22 24

Fifth Semester

Sl.No.

CourseCode


WeekRemarks

1. BICS-032 System Analysis and Design 4 4

2. BICS-033 Numerical Methods andComputation

4 4

3. BICS-034 Principles of CommunicationEngineering

4 4

4. BICS-035 Java Basics & Object Modeling &Design

4 4

5. BICSL-017 Lab IX (Communication EngineeringLab)

1 2

6. BICSL-018 Lab X(Basic Java and UML Lab) 1 2

7. BICSP-001 Project - 4

TOTAL 18 24


3/52

Sixth Semester

Sl.No.

CourseCode


WeekRemarks

1. BICS-036 Visual Basic Programming 4 4

2. BICS-037 Operating Systems 4 4

3. BICS-038 Data base Management System 4 4

4. -- Elective-I * 4 4

5. -- Elective-II* 4 4

6. BICSL-019 Lab-XI (Visual Basic Programming) 1 2

7. BICSP-001 Project 8 4

TOTAL 29 26

Any two subject are to be chosen from the following Electives.

Sl.No.

CourseCode

Course Description Credit Load perWeek

1 BICSE-005 Object Modelling And Design 4 4

2 BIELE-005 Industrial Electronics 4 4

3 BIMEE-030 Industrial Organisation And

Management4 4

4 BICSE-006 Computer Networks 4 4

1. Object Modelling And Design2. Industrial Electronics3. Industrial Organisation And Management4. Computer Networks

PLEASE NOTE

There may be some compulsory subjects / elective subjects / project where the subject codes may be

missing. The codes will be uploaded shortly.


4/52

BET-O11-MATHEMATICSI

Unit 1

Surds, Logarithms and Quadratic Equations: Surds, Logarithms, Quadratic Equations.

Unit 2

Sequences and Series: Sequences, Arithmetic Progression, Geometric Progression.

Unit 3

Binomial Theorem and Computer Mathematics: Binomial Theorem, Computer Mathematics.

Unit 4

Trigonometric Functions: Angles, Circular Functions of Trigonometric Ratios, Inverse

Trigonometric Functions.

Unit 5

Applications of Trigonometry: Properties of Triangles, Solutions of Triangles, Heights and

Distances.

Unit 6

Coordinate Geometry and Straight Line: Cartesian coordinate system.

Unit 7

Circles and Conic Sections: Circle, Conic Section.

Unit 8

Vector Algebra: Basic Concepts, Components of a Vector, Operations on Vectors, Product of Two

Vectors.

Reference:

1. Advanced Engineering Mathematics by Wartikar

2. Higher Engineering Mathematics by B S. Grewal (Khanna Publications, Delhi)

3. Engineering Mathematics by B.V. Raman (Tata McGraw-Hill).

Lectures Tutorials PracticalCredits Marks

4 0 -- 4

External:70+Internal:30

Students are required to score 35% marks

individually in both external and internal and 40%marks in total.


5/52

BET-012-PHYSICS

Unit 1

Properties of Matter: Surface Tension, Fluid Statics, Fluids in Motion, Elasticity.

Unit 2

Thermal Energy: What is Heat? Mechanical Equivalent of Heat, Modes of Heat Transfer, Kinetic

Theory of Gases.

Unit 3

Sound: Waves, Sound and its Characteristics, Speed of Sound:Newtons Formula.

Unit 4

Light: Laws of Reflection and Laws of Refraction, Image Formation by Reflecting Surfaces, Image

Formation of Refracting Surfaces, Optical Instruments, Photometry.

Unit 5

Electricity and its Effects: Electric Charge and Electric Force, Simple Electrical Circuits,

Electrical Instruments, Heating Effects of Current, Chemical Effects of Currents, Sources of EMF:

Battery.Unit 6

Magnetism: Magnetic Field, Electric Origin of Magnetism: Biot-Saverts Law, Effects o f

Magnetic Field on Electric Current, Motion of a Charged Particles in magnetic Field, Magnetic

Materials.

Reference:

A text Book of physics, (Class XI and XII) National Council for Educational Research and Training

(NCERT), New Delhi.

David Halliday and Robert Resinik, John Wiley and sons.

Alan Van Heuvelen, Physics: A General Introduction, Little, Brown and Company.

F. Bueche, Principles of physics, McGraw Hill Book Company.

Richard Wolfson and Jay M., Pasachoff, physics, Volume 1 and 2, Little Brown and Company.


3 1 -- 4





6/52

BET-013-CHEMISTRY

Unit 1

Periodic Table and Periodic Properties: Development of Periodic Table, Periodic Table and Electronic Configuration

of Elements, Periodic Properties.

Unit 2

Non-Metal: Atmosphere, Hydrogen, Oxygen, Nitrogen and Ammonia, Chlorine, Acids.

Unit 3

Metals: Occurrence and Properties of Metals, Iron and Steel, Copper, Aluminium, Alloys.

Unit 4

Water Technology: Sources of Water, Structure of Water, Solvent Action Of Water, Hardness of Water, Sludge and

Scale Formation of Boilers, Boiler Corrosion and its prevention, pH Value and Water Treatment.

Unit 5

Fuels: Classification of Fuels, Calorific Value of Fuels, Characteristics of a Good Fuel, Comparison between Solid,

Liquid, and Gaseous Fuels, Determination of Calorific Value, Solid Fuels, Liquid Fuels, Gaseous Fuels.

Unit 6

Lubricants: Lubricants, Lubrication, Selection of Lubricants, Classification of Lubricants, Lubricating Emulsion,

Gases as Lubricants, Gases as Lubricants, Properties of Lubricants

Unit 7

Polymers: Importance of Polymers, Type of Polymers, Properties of Polymers, Moulding of Plastic, Rubber

Unit 8

Glass and Ceramics :

Manufacture of Glass, Glass Transition, Varieties of Glasses, Ceramics, Refractories, Bleaching Powder, CommercialBleaching Powder

Reference:

Balram Pani (2001), A Textbook on Engineering Chemistry, Galgotia Publications Pvt. Ltd.

S.S. Kumar, S. K. Mahajan and A.S. Khatri (2001), Applied Chemistry, 6th

Edition, H. Tata Publication.

A.S. Khatri et. Al. (2004), AppliedChemistry, New India Publication.


3 1 -- 4





7/52

OIEL-001 Technical English

Lectures Tutorials PracticalCredits

Marks

4 ---- -- 4External:70+Internal:30

Students are required to score 35%

marks individually in both externaland internal and 40% marks in total.

UNIT I

Essentials of Grammar: Parts of Speech, Punctuation, Vocabulary Building, Phonetics. Office

Management : Types of Correspondence, Receipt and Dispatch of Mail, Filing Systems,

Classification of Mail, Role & Function of Correspondence, MIS, Managing Computer.

UNIT II

Letter & Resume Writing: Types of Letters-Formal / Informal, Importance and Function,Drafting the Applications, Elements of Structure, Preparing the Resume, Dos & Donts of Resume,

Helpful Hints

UNIT III

Presentation Skills: Importance of Presentation Skills, Capturing Data, Voice & PictureIntegration, Guidelines to make Presentation Interesting, Body Language, Voice Modulation,Audience Awareness, Presentation Plan, Visual Aids, Forms of Layout, Styles ofPresentation.

UNIT IV

Interview Preparation: Types of Interview, Preparing for the Interviews, Attending the Interview,Interview Process, Employers Expectations, General Etiquette, Dressing Sense, Postures & Gestures

UNIT VGroup Discussion & Presentation: Definition, Process, Guidelines, Helpful Expressions,

Evaluation

The student will be evaluated on the basis of:

1.His / Her presentation style

2.Feedback of Faculty & Students

3.General Etiquette

4.Proficiency in Letter Drafting / Interview Preparation

5.The paper is internal and at least 3 tests will be taken. Best 2 of 3 shall account for final grades

(70% Test & 30% Presentation)

References:

1. Shiv Khera, YOU CAN WIN, Macmillan Books. 2003 revised edition.2. Stephen Covey, 7 Habits of highly effective people3. John Collin, Perfect Presentation, Video Arts MARSHAL.4. Jenny Rogers, Effective Interviews, Video Arts MARSHAL.5. Raman, Sharma, Technical Communications, OXFORD.6. Sharon Gerson, Steven Gerson, Technical Writing process and product, Pearson education

Asia, LPE Third Edition.

7. R Sharma, K. Mohan, Business correspondence and Report writing , Tata McGrawHill ISBN

0-07-044555-98. Videos for Technical Education Catalog, National Education and Information Films Ltd,

Mumbai.


8/52

BET-014-Applied Mechanics

Unit 1

Coplanar and Non-coplanar Forces: System of Forces, Coplanar Force, Resultant of Concurrent

Forces, Moment of a Force, Resultant of Non-concurrent Forces.

Unit 2

Equilibrium : Free Body Diagram: Types of Supports and Constraints, Free Body Diagrams,

Equilibrium of Coplanar Forces, Plane Trusses.

Unit 3Friction: Laws of Friction, Problem Involving Dry Friction, Inclined Plane, Wedge Friction and

Screw Friction, Simple Machines.

Unit 4

Centre of Gravity and Moment of Inertia: Concept of Centre of Gravity, Moment of Inertia of

Area.

Unit 5

Rectilinear Motion, Projectiles and Relative Motion: Rectilinear Motion, Projectiles, Relative

Motion.

Unit 6

Laws of Motion:Newtons Laws of Motion, Motion on a Circular Path, Simple Harmonic Motion,

Work, Power and Energy.

Reference:

Timoshenko, S.P. and Young, D.H., Engineering Mechanics, McGraw Hill, New York.

Beer, F.P. and Johnston, E.P., Vector Mechanics for Engineering, McGraw Hill, New York.

Shames, I., Engineering Mechanics, Prentice Hall, New Jersey.

Thadani,B.N., Engineering Mechanics (Revised by J.P. Desai), Weinall Book Corporation,

Bombay, India.

Mclean and Nelson (Schaums Outline Series), Engineering Mechanics (3rd Edition).

Lecture Tutorial PracticalCredit

Marks

3 1 4


Students are required to score 35% marks individually in

both external and internal and 40% marks in total.


9/52

BETL-012: LAB-I (APPLIED SCIENCE)

List of Experiments in Physics (AnyEight)

1 To determine the density of a thin rod using balance and Vernier Callipers.

2 To determine youngs modules of the material by Searles apparatus.

3 To determine the thickness of a glass setup using speedometer.

4 To determine frequency of Tuning fork using a Sonometer.

5 To determine the velocity of sound in air by resonance tube.

6 To determine the local length of a convex lenses by displacement method.

7 To determine the refractive Index of material of the given prism.

8 To determine Verify Ohms Law using voltmeter & ammeter.

9 To determine to convert a galvanometer of given resistance into an ammeter.

10 To determine to convert a galvanometer of given resistance into an a voltmeter

11 To determine the value of unknown resistance by wheat stone bridge

12 To determine the verification of laws of series & parallel resistances.


Marks

2 1External:30+Internal:70




10/52

BETL-012: LAB-II (APPLIED MECHANICS)

List of Experiments in Applied Mechanics (AnyEight)

(1) To determine the verification of law of polygon of force.

(2) To determine the funicular polygon

(3) To determine the Finding coefficient of friction by inclined plane apparatus

(4) To determine the Mechanical, Advantage, Velocity ratio & efficiency of a

(a) Simple purchase crab winch

(b) Double purchase crab winch

(c) Gear train etc.

(d) Wheel and axle

(e) Screw Jack

(5) To determine the finding forces in members of a cantilever truss

(6) To determine the finding forces in members of a general truss

(7) To determine the moment of inertia of a flywheel

(8) To determine the Example modulus by Searles apparatus,

(9) To determine the MA, VR & n of a differential pulley block, warm & warmed

(10) To determine the finding expertly Reactions in a Beam

(11) To determine graphically evaluation of forces in a trees

(12) To determine the graphically evaluation of CG of a plane figure

(13) To determine the graphically evaluation MI of a plane figure.


Marks

2 1


Students are required to score 35% marks individually inboth external and internal and 40% marks in total.


11/52

OIEE-001: BASICS OF ELECTRICAL ENGINEERING

UNIT 1

DC CIRCUITS: Concept of electricity, Basic terms- Voltage current, Potential Difference,

Power, energy and their units. Ohms Law Effect of temperature on resistance, temperature

coefficient of resistance. Resistances in series and parallel Kirchoffs currentlaw and Kirchoffsvoltage law and their applications to simple circuits. Conversion of circuits from star to Delta

and Delta to Star. Thevenins Theorem, Superposition theorem, Nortons theorem and their use

to solve simple problems.

UNIT 2

BATTERY Basic idea about primary and secondary cells. Construction, working and

applications of Lead and Battery and Nickel Cadmium cells, Silver Oxide cells Charging

methods used for lead acid accumulator Care and maintenance of lead acid battery. Series andparallel connections of batteries.

UNIT 3

Magnetism and Electromagnetism: Introduction to electromagnetism, Magnetic field around a

straight current carrying conductor and a solenoid and methods to find its direction, force

between two parallel current carrying conductors. Force on a conductor placed in the magnetic

field. Series and parallel magnetic circuits, simple problems Importance of air gap Concept of

hysterisis and hysterisis loop.

UNIT 4

Electromagnetic Induction: Faradays Laws of electromagnetic induction. Lenzs law and

Flamings Right and left hand rules. Principle of self and mutual induction, self and mutually

induced e.m.f, simple numerical problems Energy stored in a magnetic field. Rise and decay of

current in RL and RC circuits.

UNIT 5


3 1 -- 4

External:70+Internal:30Students are required to score 35% marksindividually in both external and internal and 40%

marks in total.


12/52

AC Theory : Concept of alternating voltage and current Difference between AC and DC,

Concept of cycle, frequency period, amplitude, value, average value, r.m.s value, maximum

value, form factor and peak factor. Representation of sinusoidal quantities by phasors.

Derivation of equation of sinusoidal waveform. Physical concept of alternating voltage applied

to a pure resistance, pure inductance and pure capacitance. Inductive reactance, capacitive

reactance Alternating voltage applied to resistance and inductance in series Alternating voltage

applied to resistance and capacitance in series. Impedance triangle and phase angle ComplexNumbers-Various forms; addition, subtraction, multiplication and division, addition of

sinusoidal terms Solutions and phasor diagrams for simple practical RLC circuits (series and

parallel). Introduction series and parallel resonance and its conditions Power in pure resistance,

inductance, inductance and capacitance, power in combined RLC circuits, Power factor, active

and reactive currents and their significance, practical importance of power factor, solution of

simple circuits using j-notation. Use of conductance, succeptance and admittance.

UNIT 6

Polyphase System: Concept of polyphase in power system Advantages of 3-phase system over

single phase system. Generation of 3-phase voltages, relation between phase voltage and line

voltage, phase current, line current and power in a star and delta connected system. Simple

problems on 3-phase balanced loads and concept of unbalanced loads.

RECOMMENDED BOOKS

1) A Textbook of Electrical Technology Volume- I B.L.Theraja, S.Chand and Company

Ltd. New Delhi.

2) Basic Electrical Engineering, V.K.Mehta, S.Chand and Company Ltd., New Delhi.

3) Electrical Engineering- G.K.Mittal

4) Theory and problems of Basic Electrical Engineering- I.J.Nagrath and Kothari, Prentice-

Hall of India Pvt. Ltd.

5) Electrical Technolgy- Edward Hughes, Seventh Edition, Pearson Education

6) Elements of Electrical Technology- H.Cotton, C.B.S. Publications

7) Basic circuits analysis by John Omalley Shawn Mc Graw Hill.

8) Principles of Electrical Engineering by Del. Toro, PH


13/52

BET-016: ENGINEERING DRAWING


Marks

4 ---- -- 4


Students are required to score

35% marks individually in

both external and internal and

40% marks in total.Unit 1 INTRODUCTION TO DRAWING

Drawing Equipment and Instruments, Drawing Sheets and Layout, Sizes of Drawing Sheets,

Layout of Drawing Sheets ,Types of Letters and Lettering Standard ,Dimensions ,Style ,Recommended Sizes ,Free

Hand Lettering ,Types of Line and Their Applications ,Types of Line ,Thickness and Proportional Dimensions of

Lines ,Dimensioning of Drawing ,Elements of Dimensioning, Projection Lines, Dimension Lines and Leader Lines

,Termination and Origin Indication ,Indicating Dimensional Value on Drawings ,Arrangement and Indication of

Dimension ,Drawing Scale ,Conventional Representation

Unit 2 GEOMETRICAL CONSTRUCTION

Triangle, Square, Polygon, Pentagon, Hexagon, Circle and Curves, Conic Sections, Ellipse

Parabola, Hyperbola, Cycloid, Epicycloids, Hypocycloid, Tangent and Normal to Curve

Unit 3 ORTHOGRAPHIC PROJECTIONS-I

Orthographic Projection, Projection Methods, Designation of Views, Relative Position of View

First Angle Projection Method, Third Angle Projection Method, Indication of Method

General Principles of Orthographic Drawing ,Projection of Points ,Projections of Point Situated in the FirstQuadrant ,Second Quadrant ,Third Quadrant , Fourth Quadrant ,Projections of a Point Situated in a Plane,

Projection of Straight Lines ,Position of the Line with Respect to Planes of Projection, i.e. VP and HP May be

Traces of a Line ,True Length of a Line ,Projection of Planes

Unit 4 ORTHOGRAPHIC PROJECTIONS-II

Types of Solid, Polyhedra, Solids of Revolution, Orthographic Projections of Solid

Orthographic Projections of Solid when the Axis is Perpendicular to One of the Pr incipal Planes and Parallel to theOther Axis Perpendicular to the HP ,Axis Perpendicular to the VP

Orthographic Projections of Solid when the Axis is Parallel to Both the HP and VP

Orthographic Projections of Solid when the Axis is Inclined to One of the Principal Planes and Parallel to the Other

Principal Plane Axis Inclined to HP and Parallel to VP ,Axis Inclined to VP and Parallel to HP ,OrthographicProjections of Solid when the Axis is Inclined to Both the Principal Planes

Sections of Solid

Positions of Section Plane ,Rules for Making the Section Plane and Views ,Apparent and True Shape of Section,Methods of Drawing True Shape of Section ,Section of Polyhedra ,Section of Solids of Revolution

UNIT 5 ISOMETRIC AND OBLIQUE PROJECTIONS

Classification of Pictorial Drawings, Isometric Projection, Isometric Projection of a Cube,

Isometric Scale ,Construction of an Isometric Scale ,Isometric Drawings of Plane Geometrical Figures ,Isometric

Drawing of a Square ,Isometric Drawing of a Rectangle ,Isometric Drawing of a Circle ,Isometric Drawing of a

Triangle, Isometric Projection of Solids ,Procedure of Drawing a Cube ,Isometric Drawing of Simple Machine

Brackets ,Oblique ProjectionRules for Placing an Object, Procedure for Constructing an Oblique Drawing

UNIT 6 SURFACE DEVELOPMENT


14/52

Geometric Objects ,Development of a Surface ,Development of a Cube ,Development of a Tetrahedron,Development of a Octahedron, Development of a Prism ,Development of the Surface of a Pentagonal Prism

,Development of the Surface of a Truncated Pentagonal Prism

Development of a Pyramid, Development of the Surface of a Square Pyramid

Development of the Surface of a Truncated Pyramid, Development of the Surface of a Right Cylinder,

Development of a Right Cone, Development of a Sphere

Reference:

Bhatt, N.D., Engineering Drawing, Charotar Publishing House, New Delhi.

Narayan, K.L. and Kannaiah, P., Engineering Drawing, Tata McGraw Hill, New Delhi.

Nagar, N.K. and Purohit, R.B., Engineering Drawing-Textbook for Class XI, National Council of Educational Research

and Training (NCERT), New Delhi.


15/52

BET-026 WORKSHOP TECHNOLOGY

Unit 1

Carpentry: Classification of Carpentry Tools, Types of Work & Working Procedure, Joints in

Carpentry Work

Unit 2

Pattern Making and Foundry: Pattern making, Foundry

Unit 3

Fitting and Plumbing: Tools and Devices in Fitting work, Operation in Fitting Work, Tools inPlumbing Work, Operations in Plumbing Work, Pipe Fittings and Joints

Unit 4

Sheet Metal Work: Types of Tin-Smithy Joints, Soldering, Brazing, Fluxes, Metal Used in TinSmithy Works, Hand Tools and Machines, Sheet Metal Operation, Layout of Patterns

Unit 5

Welding: Gas Welding, Equipment for Oxy-Acetylene Gas Welding, Fluxes, Gas Flame, Arc

Welding, Polarity in Arc Welding, Electrodes for Arc Welding, Arc Welding Equipment, Arc

Welding Processes

Unit 6

Smithy and Forging: Forging Materials, Tools and Equipments used in forging, Forging

Operations, Power Hammers and Presses, Rivet, Heat treatment

Unit 7

Machine Tools: Function of Lathe, Types of Lathe, Lathe Accessories and Attachments, Lathe

Operations, Cutting Tools, Terms Used in Cutting Operation

Unit 8

Painting: Paints, Varnishes

Reference:

S.K.Hajra Choudhury, Elements of Workshop Technology, Vol-I, Manufacturing Process, Media

Promoters and Publishers Pvt Ltd.

B.S. Raghuwansi, A Course in Workshop Technology, Vol-I, Dhanpat Rai and Co. (P) Ltd., Delhi.

K.C. Arora, Workshops Practice, S.K. Kataria and Sons, Publishers and Distributors.R.K. Singhal, Workshop Practice, S.K. Kataria and Sons, Publishers and Distributors, Delhi


Marks

4 4





16/52

BET-024 E/M ENGINEERING

Unit 1

Introduction to Electricity: Electricity, Current, Resistance of a Conductor, Kirchhoffs Laws, Batteries

Unit 2

Electromagnetism, Electrostatics and Electrical Instruments:

Magnetism, Biot-Savart Law and its Applications, Electromagnetic Induction, Static Electricity,

Electrical Instruments, Hysteresis

Unit 3AC Circuits: Sinusoidal Signals, Impedance Concept, Concepts Relating to Power, Three-phase Circuits

Unit 4

Electrical Machines: DC Machines, Transformers, Distribution of Electricity

Unit 5

Units of Measurement, Gas Laws and Fuels: Basic Units of Measurement, Thermodynamic Systems, Gas Laws, Laws of

Thermodynamics, Energy Conversion Cycles, Fuels

Unit 6

Internal Combustion Engines: Classification, Cycles, Four Stroke and Two Stroke Engines, Engine Performance, Octane and

Cetane Numbers, Pollution

Unit 7

Refrigeration and Air-conditioning: Refrigeration Cycle, Vapour Compression Refrigeration, Refrigeration Capacity, Refrigerants,Absorption System, Ammonia Hydrogen Refrigeration System, Steam Jet Refrigeration, Thermoelectric Cooling, IndirectRefrigeration, Air Conditioning, Psychrometry, Comfort Air Conditioning, Summer Air Conditioning (Humid Air), Winter Air

Conditioning, Summer Air Conditioning (Dry Air), Package Air Conditioner, Evaporative Cooler, Ducting

Unit 8

Lifts and Cranes: Basic Principles, Lifts (Elevators), Escalator, Lifting of Load, Some Basic Crane Mechanisms, Types of Crane,

Rotary Cranes or Derricks

Reference:

Chakraborti, A., Circuit Theory, Dhanpat Rai Publications, New Delhi.

Fowler, Richard J., Electricity, International Edition, Tata McGraw-Hill

Publishing Co. Ltd., New Delhi.

Del, Toro V., Principles of Electrical Engineering, Prentice-Hall of India, New Delhi.

Rajput, R.K., Basic Mechanical Engineering, Laxmi Publications, New Delhi.

Bansal, R.K., Mechanical Engineering, Laxmi Publications, New Delhi.


Marks


Students are required to score 35% marks individually inboth external and internal and 40% marks in total.


17/52

OICS-001: Data Structures and Files

UNIT I

Review of 'C'

Arrays and pointers: arrays and pointers.

Functions: Parameter passing: call by value and call by reference, scope rules, and concept of

recursion and recursive functions, functions and pointers.

Structure and Union: Passing and returning structure and union as parameter for function

structure / union and pointer.

Input / Output Files: Concept, file operations, Types: sequential & random access files.

UNIT II

Introduction to data structuresOverview: Algorithm, data structure, how to create a program, how to analyze the program.

Abstract Data Types, Concept of sequential organization, concept of linear and non linear data

structure, arrays as ADT, storage representations (row major and column major). Concept of

ordered list & polynomial representation using arrays.

Searching and sorting techniques:

Searching: Basic search techniques, sequential searching, binary search, indexed sequential search.

Analysis of these algorithms.Sorting: General background, bubble sort, quick sort, selection sort, insertion sort & merge sort.

Analysis of these algorithms.

Hash Tables: Introduction, hashing functions, overflow/collision Handling.

UNIT III

Linear Data structure using linked organizationConcept of link organization: Singly linked list, doubly linked list, Circular linked list. Insertion,

deletion & traversal on above data structures. Representation & manipulation of polynomials using

linked list.

Generalized lists: Representation of polynomial using generalized list.

UNIT IV

Stacks and Queues

Stack: Definition & examples, representing stack in C, implementing stack using linked list.

Example: infix, postfix and prefix (basic definition and examples, evaluating postfix expressions,

program to evaluate postfix expression, converting infix to postfix expression, program to convert

infix to postfix).

Queues: The queue and its sequential representation, linked implementation of queues, circular

queue, and concept of priority queue.


Marks

3 1 -- 4





18/52

UNIT V

Trees: Basic terminology, binary trees, binary tree representation, binary tree traversal, primitive

operations on binary treesGraphs: Concepts and terminology, Representation of graphs using adjacency matrix, adjacency

list. Traversal: Depth first search, Breadth First Search Algorithms for minimal spanning tree and

shortest path.

References:1. C And Data structuresP.Padmanabham, BS Publications

2. C & Data Structures, Ashok N.Kamthane, Pearson Education

3. C & Data StructuresProf. P.S.Deshpande, Prof O.G.Kakde, Wiley Dreamtech Pvt.

Ltd., NewDelhi.

4. Data Structures Using CA.S.Tanenbaum, PHI/Pearson education

5. The C Programming Language, B.W. Kernighan, Dennis M.Ritchie, PHI/PearsonEducation

6. Brain W Kernighan and Denis M Ritchie- The programming Language - PHI

Publications.

7. Robert L Kruse - Data structures & program design -PHI publications (3rd

Edition).


19/52

BETL-022 LAB-III (WORKSHOP TECHNOLOGY)

List of Experiments in Workshop Technology (AnySixteen)

1. Making of lab joint, mortise and tenon-joint, Briddle joint and dovetail joint.

2. Preparation of a wooden surface for painting, apply primer on one side to paint the sameside.

3. Preparation of metallic surface for painting, apply primer and paint the given surface

4. Preparation of a metallic surface for Spray-Painting. First spray primer and paint the sameby spray-painting gun and Air-compressor system

5. Preparation of a soap-case by the metal-sheet.

6. Preparation of a funnel with thin sheet and solder the seam of funnel

7. Preparation of cylinder and solder the same.

8. Preparation of different types of joints such as Lap-joint, Butt joint, Single seam and double

seam joints etc.9. Brazing practice on small tube/ conduit joints

10. Hack sawing and chipping practice on mild steel flat.

11. Filling and souring practice of chipped M.S. job

12. Threading practice by taps and Die set.

13. Drilling practice

14. Cutting and threading practice on G.I. Pipes for using socket, elbow and tee etc and fit it onwooden practice board.

15. Sketches and study of the foundry tools, cupola and pit-furnace.

16. Preparation of green moulding sand and practice to prepare moulds.

17. Preparation of square or rectangular piece by M.S. round-rod.

18. Preparation of a hexagonal or square headed bolt.

19. Preparation of a ring with hook for wooden doors.

20. Welding practice for lap and butt joints.

21. Spot welding practice by spot welding machine.

22. Study and sketch of Lathe Machine

23. Plain turning, step-turning and knurling practice on Lathe machine24. Study and sketch of planning / shaping machines.

Lecture Tutorial PracticalCredit Marks





20/52

OIEEL-001: LAB IV (ELECTRICAL ENGINEERING)


Marks

2 1



individually in both external and internal and

40% marks in total.

LABORATORY EXPERIMENTS

1) Study of Safety precautions

2) Study of Thevenins theorem

3) Study of Kirchoffs law

4) Study of super position theorem

5) Study of RLC series circuit

6) Effect of temperature rise on conducting material

7) Direct loading test on single phase transformer

8) Study of star delta relationship

9) Study of various batteries


21/52

BET-021 MATHEMATICSII

Unit 1

Differential Calculus: Real Number System, Functions, Limits, Continuity, Derivative.

Unit 2

Applications of Derivatives: Application to Geometric, Derivative as a Rate Measure, Increasingand Decreasing Function, Maxima and Minima, Roller Theorems, Mean Value Theorem, Curve

Sketching.

Unit 3

Indefinite Integrals:Antiderivatives, Basic Definitions, Methods of Integration, Integration of

Rational Functions, Integration of Irrational Functions.

Unit 4

Definite Integrals: Definite Integrals, Fundamental Theorem of Calculus, Properties of Definite

Integrals, Applications.

Unit 5

Complex Numbers: Complex Numbers, Geometrical Representation of Complex Numbers,

Exponential and Circular Functions of Complex Numbers

Unit 6

Matrices and Determinants: Matrices, Matrix Multiplication, Determinants, Adjoint and Inverse

of a Matrix, Solution of Linear Equations with the help of Inverse of a Matrix.

Unit 7

Statistics: Statistical Data and Variables and Units of Observations, Construction of Frequency

Tables (or Frequency Distributions) from Raw Data, Graphical Presentation of FrequencyDistributions, Measures of Location and Dispersion.

Reference:

Shanti Narayan, Integral Calculus, by chand & Co.

Georgy Thomas and Ross L. Finney, Calculus and Geometry, Narosa Publishing House.

M.K. Singal and Asha Rani Singal, Complete course in I.S.C. Mathematics part-I and part-II,

Pitambar Publishing House.


Marks


Students are required to score 35% marks individually

in both external and internal and 40% marks in total.


22/52

BET-017 COMPUTER BASICS

Unit 1

Introduction to Computers: Why Computer?, Evolution of Computers, Components of a

Computer, Hardware Vs Software, System Vs Application Software, Bits and Bytes, Input and

Output Devices, ROM/RAM, Secondary Storage Devices

Unit 2Microsoft Windows: Microsoft Windows, Windows Desktop, Working With Windows, Exploring

the Control Panel, Common Accessory Applications, Windows Explorer

Unit 3

Ms Word Part I:About MS Word, MS Word Screen Layout, Creating Documents, S Word Menus,

Standard Toolbar, Formatting Toolbar

Unit 4

Ms Word II: Creating a Simple Document, Bullets, Numbering the Text, Aligning the Text,

Spelling and Grammar Check, Print Preview, Print, Saving the document, Closing the document,

Opening the document, Exiting MS Word, Selecting a Template, Starting the Template andselecting the Template Style, Header and Header Items, Recipients name and the closing items,

Header and Footer, Typing the Text, Creating and modifying tables, Creating rows and columns,

Inserting rows and columns, Merging rows and columns,

Unit 5

Introduction to Spreadsheets Part-I:Starting MS Excel, Excel Screen Layout, Excel Menu

Unit 6

Ms Excel Toolbars: Standard Toolbar, Formatting Toolbar, Creating a Simple Worksheet,

Functions

Unit 7

Ms PowerPoint: About PowerPoint, Toolbars, Creating a simple presentation, Making your

presentation attractive, Viewing a presentation, Printing a presentation, Getting Help

Unit 8

Internet and E-Mailing: Internet Basics, Starting the Internet, Searching, E-mailing, Internet Chat

Reference:

Saxena, Sanjay, A First Course in Computer, 2003 Edition, Vikas Publishing House Pvt. Ltd., New Delhi.

Alexis, Leon and Mathews, Leon, Fundamentals of Information Technology, Vikas Publishing Hopuse Pvt. Ltd., New Delhi.

Stephen L. nelson, Office 2000: The Complete Reference, Tata McGraw Hill Publishing Company Ltd., New Delhi.

Joe Hubraken, Microsoft office 2000: 8 in 1, Prentice Hall of India, New Delhi.

Lecture Tutorial Practical CreditMarks

4 4





23/52

Basandra, S.K., Computer Today, Galgotia Publication, New Delhi.

BET-022 STRENGTH OF MATERIALS

Unit 1

Stresses and Strains: Basic Concepts, Mechanical Behaviour of Materials, Deformation of Bars,

Composite Bars, Thermal Stresses and Strains, Relationship between Elastic Constants.

Unit 2

Principal Stresses: State of Stresses, Normal and Shear Stresses, Stress on Oblique Sections,

Principal Stresses and Principal Planes.

Unit 3

Shear Forces and Bending Moments: Beams, Shear Force and Bending Moment, Shear Force and

Bending Moment Diagram.

Unit 4

Stresses in Beams: Simple Bending or Pure Bending, Moment of Resistance, Bending Stress

Distribution, Practical Applications, Section Modulus, Shear Stress Distribution in Beams.

Unit 5Deflection of Beams: Curvature of Bending Beam, Differential Equation of Deflection Curve,

Double Integration Method for Slope and Deflection.

Unit 6

Torsion: Torsion of Circular Shafts, Power Transmission by Shafts.


3 1 4External:70+Internal:30

Students are required to score 35% marks individually

in both external and internal and 40% marks in total.

Unit 7

Columns and Struts: Failure of a Column or Strut, Sigh Conventions, Types of End Condition of

Columns, Equivalent Length of a Column, Slenderness Ratio, Factor of Safety, Indian StandardSpecifications for Columns.

Reference:

Timoshenko, Stephen, Strength of Materials-part I and part II, CBS Publishers and Distributors.

Schaums Outline Series (1989), Strength of Materials- Second Edition, McGraw Hill Book

Company.

Popov, E.P.(1993), Mechanics of Materials-Second Edition, Prentice Hall of India Private Limited.

Ryder, G.H. (1993), Strengthof Materials, Educational Low Priced books Scheme.Case, John, Chilver, L. Ross, Carl T.F. (1993), Strength of Materials and Structures-Third Edition,

Educational Low Priced Books Scheme.


24/52

Dr. B.C. Punamia, Strength of Materials and Mechanics of structures.

Dr. Surendra Singh, Strength of Materials.

BICS-027: Computer Organization

UNIT IComputer Fundamentals: Block structure of a computer, characteristics of computers, generationof computers, and classification of computers. Number System: Bit, byte, binary, decimal,

hexadecimal, and octal systems, conversion from one system to the other, Binary Arithmetic:Addition, subtraction and multiplication. Representation of Information: Integer and floating pointrepresentation, Complement schemes, Character codes (ASCII, EBCDIC, BCD, Excess-3, Grey).

UNIT IIElements of a computer processing system: HardwareCPU storage devices and media, VDU,input- output devices, data communication equipment. Software system software, applicationsoftware.Programming languages: classification, machine code, assembly language, higher level language,and fourth generation languages

UNIT IIIOperating system : Batch, multi-programming, time sharing, multiprocessing, PC operatingsystem, network operating system, on-line and real time operating system.

UNIT IVComputer Network and Communication: Network types, network topologies, networkcommunication devices, physical communication media, network protocol, (TCP/IP.) Internet andits Applications: E-mail, TELNET, FTP, World Wide Web, Internet chatting.

UNIT VRange of application : Scientific, Business, educational, weather forecasting, and remotesensing, planning, multilingual applications, management information, decision support system,

inventory control, medical, industrial control, banks, railways, etc.

References:

1. Foundations of Information Technology 3/e (Paperback - 2005) by D. S. Yadav2. Foundations of Information Technology by Kahate3. Foundations of Information Technology in the Era of Network and Mobile Computing

Series: IFIP International Federation for Information Processing , Vol. 96 Baeza-Yates,

Ricardo; Montanari, Ugo; Santoro, Nicola (Eds.) 2002, 627 p., Hardcover ISBN: 978-1-

4020-7181-2


Marks

3 1 -- 4External:70+Internal:30


individually in both external and internaland 40% marks in total.
http://www.flipkart.com/d-s-yadav/http://www.springer.com/series/6102http://www.springer.com/series/6102http://www.springer.com/series/6102http://www.flipkart.com/d-s-yadav/


25/52

BIEL-027: Applied Electronics

UNIT I

Amplifiers: 1) Power Amplifiers: Introduction, ClassificationClass A, Class B, Class AB & Class C, efficiency of

each. Single stage class A power amplifier: Circuit operation, input & output waveforms, graphical Analysis and

efficiency of i] Transformer couple resistive load single stage power amplifier. ii] Class A push pull amplifier. iii] Class

B push pull amplifier. iv] Class AB push pull amplifier. Concept of cross over distortion Advantages of push pull

amplifier, collector power dissipation requirement & specifications of power transistor, need of heat sink.

2) FET Amplifier: Biasing of FET: Source Self Bias, Drain to source Bias, Application of FET as VVR, CommonSource Amplifier: Working & Applications, Introduction to MOSFET Types, Construction, Working & Applications

3) Tuned Amplifiers: Introduction & necessity of tuned amplifier. Basic tuned circuits, series & parallel resonance in

tuned circuits. Operating principle, circuit working, resonance frequency of single tuned, double tuned amplifiers.

UNIT II

Feedback Amplifiers & oscillators: General theory of feedback: Types of feedback -negative & positive feedback.

Types of negative feedback - voltage shunt, voltage series, current shunt & current series. Advantages of negative

feedback on voltage gain, bandwidth, input impedance, output impedance, stability, noise, distortion in amplifiers.

Introduction to oscillator, block diagram of sine wave oscillator, requirement of oscillation - Barkhausen criterion,

operating principles of RC & LC oscillators RC oscillators RC phase shift, Wien bridge LC oscillators - Colpitts,

Hartley, Crystal oscillators Circuit diagram, equation for frequency of oscillation & frequency stability.

UNIT IIIWave shaping circuits: Necessity of wave shaping circuits, Linear circuits RC integrator & differentiator- input/

output waveforms & frequency response. Non - linear circuits - Clipper, diode series & shunt, positive & negative

biased & unbiased & combinational clipper. Clampers- positive & negative clampers.

UNIT IV

Multivibrators: Transistor as switch. Definition & graphical representation of different time periods. Multivibrator

classification, circuit working & frequency with specific application. MMV, AMV, BMV & Schmitt trigger

UNIT VTime base generator: Voltage time base generator, exponential sweep generator UJT Relaxation Oscillator, negative

resistance generator. working principle & operation. Current time base generator, bootstrap & miller sweep generator ,

applications in TV & CRO.

UNIT VI

Trouble shooting & Testing:Need for trouble shooting, Important steps for testing Visible testing - Observing circuits

for visible faults like broken component, open contacts etc. Active testing - Voltage analysis, Resistance analysis, signal

analysis. Trouble shootings of multivibrators, phase shift oscillators, transistorised sweep generator, clipping &

clamping circuits.

References:

1. Paul Malvino, Electronic Principles, Tata McGraw-Hill

2. R.S.Sedha, Applied Electronics, S.Chand & Co.

3. Allen Mottershed,Electronics Devices & Circuits, Prantice Hall India LTD.

4. J.Millman and H.Taub, Pulse Digital & Switching Waveforms, Tata McGraw-Hill5. G.K.Mittal and A.R.Vanvasai, Pulse & Digital Electronics , Khanna Publication


3 1 -- 4External:70+Internal:30

Students are required to score 35% marksindividually in both external and internal and 40%

marks in total..


26/52

BICEL-016: Lab-V (Computer Applications)





List of Practical : (Any Ten)

1. Installation of PC, connecting and disconnecting key board, monitor and printer, correct methodof handling floppies, disks and mouse

2. Exploring the control panelchanging date & time, Desktop Background, Screen Saver, Add orRemove Programs.

3. Creating & Deleting folders, opening files/folders, copying files, renaming files/folders,changing folder view

4. To prepare captions in different sizes and fonts and generate tables in MS Word and usingwindows.

5. Creating & modifying tables in MS word.6. Creating documents in MS Word and working with MS Word menus.7. To prepare tables and charts in MS Excel using windows.8. Creating a worksheet and working with functions in MS Excel9. Creating a presentation/slide-show in MS PowerPoint10.Creating an E-mail Account, checking & sending E-mail, E-mail attachments & Internet

Chatting.

11.Developing a Technical Report with tables in MS word.12.Creating a presentation for the Technical Report in MS PowerPoint.


27/52

BMEL-008: Lab-VI (Strength of Materials)

Lecture Tutorial Practical

Credit Marks

2 1



individually in both external and internal and

40% marks in total.

List of Experiments in Strength of Materials (AnyEight)

1. To determine shear force (SF) and Bending moment (BM) diagram at various sections of asimply supported beam loaded with several point load on plain paper.

2. To determine yield stress, ultimate stress, youngs modulus, percentage elongation of a mildsteel rod by Universal testing machine.

3. Determination of bending test on timber.

4. Determination of bending test on floor tiles.

5. Determination of modulus of rigidity of a curve by torsion apparatus.

6. Determination of deflection and stiffness of a helical spring.

7. To determine hardness of a plate by Rock wells Brinells hardness testing machine.

8. To determine impact resistance of a material by Izode impact testing machine.

9. To determine compression test on timber, bricks, mild steel and copper.10.Determination of water absorption test on bricks.

11.Determination of water absorption test on floor tiles.

12.To determine the moisture content and specific gravity of timber.


28/52

BICS-028: PC ASSEMBLY & MAINTENANCE

UNIT I

Introduction to PC: Hardware components- study of motherboards- Different types of ports, slots andconnectors- Add on cards-power supply- SMPS- function & operations.

UNIT II

Storage Devices: Floppy Disk Controller- Disk Physical specification & operations- Disk magneticproperties- Cylinders- Clusters- Hard disks- Hard disk drive operation- Magnetic data storage- Sectors- DiskformattingpartitioningHard disk features- Hard disk data transfer modesProgrammed I/ODirect

memory access- Ultra DMA- Data addressingStandard CHS addressingExtended CHS addressingLogical Block Addressing.

UNIT III

Optical storage : CD ROM, CD Technology, Sector layout, CD-R, CD-RW, CDROM, drive specifications-data transfer rate- Access time- Constant linear velocity- constant angular velocityBuffers- Interface-Magneto optical drives- WORM devices- DVD- RAIDHolographic storage.

UNIT IV

Memory Management in PC

ParityECC-Static & Dynamic RAM- Memory AddressingSegmented addressing g- 64KB Limits- 640KB barrier- Logical, segmented, virtual, linear and physical memory addresses- Extended and Expanded

memory- Cache memory- Video memory- HMA- Flat memory model- Advanced memory technologies.

UNIT V

Bus Structure: ISA, PCI, PCMCIA, AGP,USB, Hard Disk Interfaces- IDE, EIDE, ATA- Communication

ports- SerialParallel port- Keyboard/ Mouse Interface connectors.

References

1. PC Hardware Complete ReferenceCraig Zacker & John Rourke, Tata McGraw Hill2. The Indispensable PC Hardware Book- Messmer, Pearson Education3. Troubleshooting and Repairing Your PCCoery Candler, Wiley4. Upgrading and repairing PCs (4th edition)- Scoot Mueller, Pearson Education5. IBM PC Assembly Language ProgrammingAbel, PHI6. The Complete PC Upgrade & Maintenance Guide by Mark Minasi, Eight Edition, BPB.7. Peter Nortons Inside the PC by Peter Norton, (8th Edition)8. Upgrading & Fixing PCs for Dummies by Andy Rathbone.9. PC Upgrading Maintenance & Trouble shooting guide- Dr. S.K. Chauhan, Kataria


3 1 -- 4

External:70+Internal:30Students are required to score 35% marks



29/52

BICS-029: ALGORITHMS AND LOGIC DESIGN

UNIT I

Algorithm: Definition, Characteristics, Uses of Algorithm, Development of Algorithms.Flowchart: Components of Flowchart, Design of Flow chart for various problems.PsuedoCode: Definition, & use.Recursive Algorithms

UNIT II

Searching Techniques: Straight Sequential Search, Binary Search (recursive & non recursive Algorithms),and Fibonacci Search.

UNIT III

Sorting Techniques: Introduction, Sorting by exchange, Bubble sort, Selection sort, Insertion sort, Bucket

sort, Shell sort, Merge sort, & Quick sort.

UNIT IV

Study of Algorithm: How to devise algorithms, How to validate algorithms, How to analyze algorithms,How to test a program, How to Create a Program, Program development cycle.

UNIT V

Analysis: Mathematical background, The model, The time complexity: How to analyze and measure, Big-Oh and big- Omega notations, Best case, average case and worst case analysis.

Reference

1. Fundamentals of computer Algorithms by Horowitz, Sahani, Rajasekaran, Galgotiapublications

2. Introduction to Algorithms by Cormen.


3 1 -- 4



individually in both external and internal and 40%

marks in total.


30/52

BICS-030: CPROGRAMMING

UNIT 1

Information Storage and Retrieval. Need for information storage and retrieval. Creating data base file.Querying database file on single and multiple keys. Ordering the data on a selected key. Programming a verysimple application.

UNIT 2

Programming in C.Basic structure of C programs. Executing a C program. Constants, variables, and datatypes. Operators and expressions. Managing Input- Output operations like reading a character, writing a

character, formatted input, formatted output through print, scan, getch, putch statements etc. Decisionmaking and branching using IFelse, switch, go to statements. Decision making and looping using do-while, and for statements. Arraysone dimensional and two dimensional.

UNIT 3

Computers Application Overview. Commercial and business data processing application. Engineeringcomputation. CAD, CAM, CAE, CAI. Typical Applications.

UNIT 4

Students will be required to make a small programe for analysis of circuits design in Electrical Engineeringcomponents or any other area. Use and introduction of various software available in the field of electricalengineering.

RECOMMENDED BOOKS

1. Programming in C by Sachaum Series, McGraw Hills2. The essentials of Computer Organizing and Architecture by Linda Null and Julia Labur, narosa

Publishing House Pvt.Ltd., New Delhi3. Programming in C by Kerning Lan and Riechie Prentice Hall of India, New Delhi4. Programming in C by Balaguru Swamy, Tata McGraw Hill, New Delhi5. Let us C- Yashwant Kanetkar, BPB Publications, New Delhi6. Vijay Mukhi Series for C and C++7. Elements of C by MH Lewin, Khanna Publishers, New Delhi8. Programming in C by kris A Jansa, Galgotia Publictions Pvt.Ltd., Daryaganj,9. Programming in C by R Subburaj, Vikas Publications House Pvt.Ltd., Jangpura,10.Programming in C by BP Mahapatra, Khanna Publishers, New Delhi


4 0 -- 4

External:70+Internal:30Students are required to score 35% marks



31/52

BICS-31: BASICS OF NETWORKING

UNIT I

Basic Network Concepts:Understanding Network: Human Networks, Computer Networks, Network PlanIdentifying the Benefits of Network: Sharing Information, Sharing ResourcesFacilitating Centralized Management: Managing Software, Maintaining the Network, Backing Up Data.

Distinguishing between Network classifications: Classifying Network by their Geography- LAN, MAN,WAN.Classifying Networks by their Component Role: Peer to Peer, Server based Network.Network Features: File Sharing, Printer Sharing, Application Services, E-Mail, Remote Access.

UNIT II

Network Topologies and Networking Devices:Types of Topology- Bus Topology, Ring Topology, Star Topology, Mesh Topology, Tree Topology, HybridTopology.Network Control Devices- Hubs, Switches, Routers, Bridges, Repeaters, Gateways, Modems

UNIT III

Transmission Media:

Guided Media- Twisted PairUTP, STP, Coaxial Cable; Optical Fibre Structure, Light Source for Fibre,Propagation Mode, Advantages of optical fibre, and Disadvantages of optical fibre, and Disadvantages ofoptical fibre.

Um-Guided Media: Wireless Communication- Communication Band; Microwave Communication;Satellite Communication- Access Method; Cellular (Mobile) Telephone- Band in Cellular Telephony, Calls

Using Mobiles Phones, Transmitting receiving operations; New Developments.

UNIT IVNetwork Reference Model:OSI Reference Model- Interlayer Communication- Data Encapsulation, Horizontal Communication, VerticalCommunication, Encapsulation Terminology; Physical layer; Data link layer; Network layer; Transportlayer; Session layer; Presentation layer; Application layer.

TCP/IP Reference Model- Link; Internet; Transport; Application layer.Comparison of the OSI and TCP/IP reference models.

UNIT V

TCP/IP Protocols- SLIP and PPP; ARP; IP; ICPM; TCP and UDP.IP AddressingIP Address Assignments; IP Address Classes; Subnet Masking; Registered and unregisteredAddresses.

TCP/IP Configuration- Installing the TCP/IP Protocol; Configuring TCP/IP- Configuring Basic TCP/IPProperties, Configuring Advanced TCP/IP Properties

References:

01 Introduction to Networking Richard A.McMohan, Sir Tata McGrawHill Edition02 Networking + Certification (Second Edition) Microsoft Press

03 Complete Reference Networking Craig Zacker Tata McGrawHill Edition04 Data Communication and Networking Achyut S.Godbole Tata McGrawHill Editio


4 0 -- 4



individually in both external and internal and 40%

marks in total.


32/52

BIEE-32: Principles of Computer Architecture

UNIT I

Motherboard And Its Components: Different types of PC configurations and their comparison,

Chipset basic, chipset Architecture : North/South Bridge, architecture and Hub architecture,

Architecture of Intel chipset 915 G& 945 G, Overview and features of ISA, PCI-X, PCI-Xpress,

AGP, Processor Bus (no pin description) Comparison between PCI and PCI Express, Logical

memory organization : Conventional memory, Extended memory, Expanded memory (No memory

map), Concept of cache memory : Internal cache, External cache, (L1, L2, L3 cache), Overview and

features of SDRAM, DDR, SDRAM, DDR2, SDRAM, DDR3, BIOS Basics

UNIT II

Storage Devices And Its Interfacing: Recording Technique : RM, MFM, RLL Perpendicular,

magnetic recording, Hard disk construction and working, Terms related to Hard Disk : Track,

Sector cylinder, cluster, Head parking, MBR, Zone recording, Formatting, Low level formatting,

High level formatting, partitioning, Hard disk drive interface : features of parallel AT attachment,

(PATA), Serial AT Attachment (SATA), External SATA (no pin description), CDROM drive :

Construction, recording, DVD : Construction, Recording

UNIT III

Display Devices & Interfacing: CRT colour monitor : Block diagram and function of each block,

Characteristics of CRT monitor: Dot pitch, Resolution, Video bandwidth, Horizontal scanning

frequency, Interlaced versus non interlaced monitor, Advantages of CRT display over LCD display,

LCD monitor : functional block diagram of LCD monitor, working principal, advantages and

disadvantages Types : Passive matrix and Active matrix, Important characteristics : Resolution,

Refresh rate, Response time. Basic block diagram of a video accelerator card

UNIT IVInput & Output Devices: Construction, working & Installation of : Keyboard. Mouse: Mechanical,

Opto mechanical, New optical, Scanner: Types, Flat bed, Block diagram and specifications.

Modem: Internal and External: Block diagram and specifications. Printer: Dot matrix, Inkjet, Laser:

Block diagram and specifications

UNIT VPower Supplies: Block diagram and working of SMPS. Signal description and pin diagram of AT

and ATX connectors, Power supply characteristics: Rated wattage, Efficiency, Regulation, Ripple,

Load regulation, line regulation, Power problems : Blackout, Brownout, surges and spikes,

Symptoms of power problems, Protection devices : Surge suppressor : working UPS : Block

diagram, working, Types, Rating

UNIT VI


3 1 -- 4





33/52

Interfaces: SCSI cables and connectors, SCSI drive configuration. USB features, RS232 : (Voltages

& 9 pin Signal description), Centronics (interface diagram, signals and timing waveform), Firewire

features

Pc Diagnostic, Testing And Maintenance And Tools: Preventive Maintenance : Active Preventive

maintenance, passive preventiv maintenance, periodic maintenance procedure Preventive

maintenance of peripherals of PCs. Fault finding and troubleshooting of the above peripherals,

ESD (Electrostatic discharge), RFI protection, Working of logic probe, logic purser, current

Reference Books:

1.Mike Meyers, Scott Jerni gan, Managing & Troubleshooting PCs TMH

2. Bigelow, Bigelow's Troubleshooting, Maintaining & Repairing PCs TMH

3. Mark Minasi, The Complete PC Upgrade & Maintenance Guide BPB Publication

4. D. Balasubramanian, Computer Installation & Servicing Tata McGraw Hill

5. Scott Mueller , Upgrading & Repairing PCs Pearson Education


34/52

BICSL-015: LabVII (PC ASSEMBLY)

List of Practical

1. To check and measure various supply voltages of PC2. To make comparative study of motherboards.3. To observe and study various cables, connections and parts used in computer communication.4. To study various cards used in system viz. display card, LAN card etc.5. To remove, study and replace floppy disk drive.6. To remove, study and replace hard disk.7. To remove, study and replace CD ROM drive.

8. To study monitor, its circuitry and various presents and some elementary fault detection.9. To study printer assembly and elementary fault detection of DMP and laser printers.10.To observe various cables and connectors used in networking.11.To study parts of keyboard and mouse.12.To assemble a PC13.Troubleshooting exercise related to various components of computer like monitor, drives, memory

and printer etc.14. Installation of Operating System (Window & Linux).

Design Problems:

1. Reformatting a disk does not erase the data on the disk, only the address tables. Recover the datafrom a disk which has been accidentally formatted.

2. Assembly of a PC right from scratch, and install the necessary software.3. Try for an innovative idea through which the hard disk might be designed.4. Understand and install appropriate operating systems and drives.5. Perform periodic maintenance on a computer workstation.6. Demonstrate knowledge of computer architecture, i.e., power supplies, motherboards, memory,

processors, hard drives, modems, and bus and port connections.7. Apply techniques used in the repair and building of computers and their integrated components.8. Demonstrate knowledge of installation and maintenance of computer peripherals.9. Understand and troubleshoot basic computer networks.


Marks





35/52

BICSL-016: LAB-VIII ( C PROGRAMMING)

LABORATORY EXPERIMENTS:-

1. Creating database2. Querying the database3. Report generation4. Programming in dbase5. Use of spread sheets/Matlab/mathematics/Eureka (or any other package) for engineering computers.6. Use of design packages (appropriate design packages may be selected depending upon the

availability) on Estimating and Costing, Analysis of rates and other areas.

7. Use of and electrical engineering related CAI packages8. Programming for DAS and control.9. Exercise on data acquisition.10.Exercise on controlon/off switch, and proportional control.11.Programming exercise on executing C program12.Programming exercise on editing C program13.Programming exercise on defining variables and assigning values to variables.14.Programming exercise on arithmetic expressions and their evaluation.15.Programming exercise on arithmetic and relational operators.16.Programming exercise on reading a character.17.Programming exercise on writing a character.18.Programming exercise on formatting input using print.19.Programming exercise on formatting output using scan.20.Programming exercise on simple if statement.21.Programming exercise on IF. else statement.22.Programming exercise on switch statement.23.Programming exercise on go to statement24.Programming exercise on do- while statement.25.Programming exercise on for statement26.Programming exercise on one-dimensional arrays.27.Programming exercise o two- dimensional arrays.28.Exercise on- Internet use/applicationTypical application on Electrical Engineering


Marks





36/52

BICS-032: SYSTEM ANALYSIS & DESIGN

UNIT I

Fundamentals of System Development: System Concept- Characteristics- Elements of System-

Types of System- Modern Approach to System Analysis and Design- System Development Life

Cycle- Appropriate to Improving DevelopmentTools for System Development- Succeeding as a

System AnalystSkillsManaging the Project.

UNIT II

System Analysis: Determining System Requirements- Traditional Methods- Modern Methods-

Radical Methods- Structuring System Requirements- Process ModelingData Flow DiagrammingLogic ModelingConceptual Data ModelingE-R Modeling.

UNIT III

System Design: System Implementation- Software Application TestingInstallation-

DocumentationTraining and Support- Organizational Issues in System Implementation-

Maintaining Information System- Conducting System Maintenance.

UNIT IV

Implementation And Maintenance: System Implementation- Software Application Testing

InstallationDocumentationTraining and Support- Organizational Issues in Systems

ImplementationMaintaining Information System- Conducting System Maintenance.

UNIT VAdvanced Analysis And Design Methods: Rapid Application DevelopmentComponents of

RAD- Approaches to RAD- Advantages and Disadvantages- Object Oriented Analysis and Design-

Object Oriented Development Life Cycle- The Unified Modeling LanguageObject Model

Dynamic ModelingProcess ModelingAnalysis versus Design.

References1. Jeffrey A.Hoffer, Joey F. George, Joseph S.Valacich, Modern System Analysis and

Design, Third Edition, Pearson Education, Asia, 2002.

2. Elias M. Awad, System Analysis and Design, Galgotia Publications Pvt.LTd., eleventhEdition, 1991.

3. Lee, Introducing System Analysis and Design, Volumes 1&11, Galgotia BookSource,1995.

4. Rajaraman, V, Analysis and Design of Information System, PHI Pvt.Ltd., 19915. Perry Edwards, System Analysis and Design, McGraw International Edition, 1993.6. Booch Grady, Object Oriented Analysis and Design, Addisson Wesley, fifth Edition,

1997.

7. Rumbaugh et al, Succeeding with Booch and Rambaugh Methods, Addisson Wesley,second Edition, 1998.

8. Viswanadham, N and Narahari, Y, Performance modeling of automated system, PrenticeHall, 1996.


3 1 -- 4



marks in total.


37/52

BICS-033: NUMERICAL METHODS & COMPUTATION

UNIT I

Errors in Numerical Computations: Their types, analysis and estimation, numerical

instabilities in computation.

Solutions to Transcendental and Polynomial equations: Bisection method, secant method,

Regula Falsi method, Newton Raphson method for polynomial equations.

UNIT IISolution to System of Linear Algebraic Equations. Cramers rule, Gauss elimination

method, Gauss Jordan method, Triangularization methods- Gauss Siedel method of

iternation.

UNIT III

Interpolantion and Approximation: Linear interpolation and high order interpolation

using Lagrange and Newton Interpolation methods, finite difference operators and

interpolation polynomials using finite differences. Approximations- least square

approximation techniques, linear regression.

UNIT IVNumerical Differentiation: Methods based on interpolation and finite differences.

Numerical Integration: Trapezoidal rule, mid- point method, Simpsons 1/3rd and 3/8th rule.

Solution to ordinary differential equations: Taylor series method, Picards method of

successive approximation. Eulers method, Eulers predictor and corrector method. Runge

Kutta method for 2nd and 4th order. Initial and boundary value problems.

UNIT V

Numerical Optimization: Golden section search, Brents method, minimization using

derivatives, introduction to linear programming.

References:1. NUMERICAL METHODS: for Mathematics, Science and Engineering , 2nd Ed,

1992 John H.Mathews

ISBN: 0-13-625047-5 Prentice- Hall International (UK) Limited London

2. NUMERICAL METHODS: Using C, Fourth Edition, 2004 John H. Mathews andKurtis D. Fink

ISBN 0-13-065248-2 Prentice-Hall Pub. Inc.Upper Saddle River, NJ

3. Applied Numerical Methods in C (Hardcover) by Shoichiro Nakamura (Author).


3 1 -- 4



marks in total.


38/52

BICS-034: Principles of communication Engineering

UNIT I

Introduction to electronic communication: Importance, Block diagram of communication system,

Modulation, Need for modulation, Types of Electronics communications, Simplex & DuplexFull

& Half, Digital Analog Applications of communication. The electromagnetic spectrum (different

bands & their frequencies) Concept of Transmission bandwidth.

UNIT II

Amplitude modulation & Frequency modulation: Definition, Modulation indexdefinition, its

effect on, modulated signal, simple numerical. Mathematical representation of amplitude modulated

wave & its meaning (concept of sidebands) Bandwidth requirement, Representation of AM signal in

time & frequency domain. Power relation in AM wave, simple numerical. Frequency modulation

(definition). DefinitionDeviation ratio, max. Deviation ratio. Mathematical representation of

frequency modulation and its meaning. Representation of frequency modulated signal in time

domain and frequency domain. Bandwidth requirementsimple numerical FM signal generation

using reactance modulator circuit (transistorized). Concept with graph-pre emphasis and

deemphasis. Block diagram of FM transmitter explanation with waveform (Armstrong frequency

modulation system)

UNIT III

Radio receivers (AM & FM): Principle of heterodyne, Block diagram of super heterodyne receiver

and its working with waveforms. Characteristics of AM radio receiver- Sensitivity, Selectivity, and

Fidelity. Demodulation of AM signal. Need of AGC and its typesimple, delayed (with graph)

Block diagram of FM receiver explanation with waveform. FM Detectorslope detection,

transformer action at above & below resonance ratio detector (diode circuit), PLL (block diagram

and operation) explanation with vector diagram.

UNIT IV

Transmission lines: Fundamentals of transmission line. Equivalent circuit of transmission line

General equivalent circuit RF equivalent circuit Characteristics impedance, methods of calculations

& simple numerical. Losses in transmission line. Standing waveSWR, VSWR, Reflection

coefficient, simple numerical. Quarter wave & half wavelength line Impedance inversion by quarter

wavelength line Quarter wave transformer & impedance matching Properties of line of various

lengths. Impedance matching Stubssingle & double, Balun

UNIT V

Antennas: Antennas fundamentals. Radiation mechanism. Concept & definition of polarization,bandwidth, beam width, antenna resistance, directivity, antenna gain, power density. Dipole antenna

Half wave dipole antenna Radiation pattern Folded dipole antenna & its radiation pattern.

Structure, Radiation pattern & applications of the following antennas.


4 0 -- 4



marks in total.


39/52

i) Loop antenna, ii) Ferrite loop antenna, iii) Telescopic antenna, iv) Yagi-uda antenna, v)

Microwave antennas- Dish antenna & Horn antenna.

UNIT VI

Wave Propagation: Fundamental of electromagnetic wave. Transverse electromagnetic wave,

polarization. Ground wave Ionosphere Sky wave propagation Concept of actual height and virtualheight. Definitioncritical frequency, max. useable frequency, skip distance, fading Space wave

propagation. Duct propagation Troposphere scatter propagation

Reference Books:

1. George Kennedy Electronic Communication System Tata McGraw-Hill

2. Roddy Collen Electronic Communication Prentice Hall India

3. Louis E. Frenzel Communication Electronics Tata McGraw-Hill

4. Hsu & Mitra Analog & Digital Communication- Tata McGraw-Hill


40/52

BICS-035: Java Basics & Object Modeling & Design

UNIT I

Fundamentals of Java : Advantages of java, Java programming paradigm

Programming in Java : Building Java application (no Java Applets), OO Mechanism in Java, Class definition,

Constructor, Inheritance, Polymorphism

Interfaces and Packages : Interfaces in Java, Packages in Java

Exception handling in Java : Built-in classes, Mechanism, Error handling

UNIT II

Importance of Modeling: Brief overview of Object Modeling Technology (OMT) by Ram Baugh, Booch

Methodology, Use Case driven approach (OOSE) by Jacobson, Overview of CRC card method by Cunningham.

Object Modeling: Objects and Classes (Object Diagrams, Attributes, Operations and Methods), Links, Associationsand Advanced Concepts (General Concepts, Multiplicity, Link Attributes, and Association as a Class, Roll names,

Ordering, Qualification, and Aggregation). Generalizations and Inheritance, Grouping Constructs. Aggregation verses

Association and Generalization, Recursive Aggregates, and Propagation of Operations. Abstract Classes, Multiple

Inheritance, Metadata, Candidate Keys, Constraints Introduction to Dynamic and Functional Modeling.

UNIT III

Overview of UML: Efforts of standardization / Integration, OMG approval for UML, Scope of UML, Conceptual

model of UML, ArchitecturalMetamodel, Unified Software Development Lifecycle. Introduction to UML Diagrams

UNIT IV

UMLStructural Modeling: Advanced Class Diagrams: - Advanced Classes and Relationships, Interfaces, Types and

Roles, Packages, Instances. Object Diagrams. Component Diagrams: Terms and Concepts, Common modeling

techniques. Deployment Diagrams: Terms and Concepts, Common modeling techniques.

UNIT V

UML Behavioral Modeling: Use case diagram: Terms and Concepts, Modeling techniques. Interaction diagram

(Sequence and collaboration diagram): Terms and Concepts, Modeling techniques. State chart diagram: Terms and

Concepts, Modeling techniques. Activity diagram: Terms and Concepts, Modeling techniques.

References:

1. Grady Booch, James Rumbaugh, Ivar Jacobson: The Unified Modeling Language User Guide, PearsonEducation.

2. Hans-Erik Eriksson, Magnus Penker, Brian Lyons, David Fado: UML 2 Toolkit, WILEY-Dreamtech India Pvt.Ltd.

3. D. Samanta, Object Oriented Programming with C++ and Java, PHI4. Herbert Schildt, Java 2 Complete Reference, TMH5. Meilir Page-Jones: Fundamentals of Object Oriented Design in UML, Pearson Education.6. Pascal Roques: Modeling Software Systems Using UML2, WILEY-Dreamtech India Pvt. Ltd.7. Atul Kahate: Object Oriented Analysis & Design, The McGraw-Hill Companies.8. Mark Priestley: Practical Object-Oriented Design with UML,TATA McGrawHill9. Appling UML and Patterns: An introduction to Object Oriented Analysis and Design and Unified Process,

Craig Larman, Pearson Education.


3 1 -- 4





41/52

BICSL-017: Lab-IX( Communication Engineering)

List of Practical: (Any Ten)

1. Observe AM Signal on Spectrum Analyzer

2. Observe FM wave & calculate modulation index.

3. Visit to transmitter station & prepare a report.

4. Draw the circuit diagram & layout of AM radio receiver.

5. Voltage waveform analysis at various points in AM radio receiver.

6. Observe input & output waveforms of AM detector.

7. Plot graph of sensitivity of receiver.

8. Plot graph of selectivity of receiver.

9. Plot graph of fidelity of receiver.10. Fault finding of AM radio receiver.

11. Create two faults in each section OR fault finding in FM radio receiver, Create two faults in

each section

12. Prepare a report on different types of radio receivers available in market. find out

their specifications, IC used etc

13. FM detector characteristics.

14. Measure the length of directors, reflectors, dipoles and spacing between them of Yagi uda

antenna and compare with the theoretical value.

15. Plot the directional pattern of given antenna.

Design Problems:

1. AM/FM Radio Receiver/Transmitter using transistor

2. AM modulator/detector/mixer using diode.

3. FM detector

List of Equipments:1. AM signal Trainer kit

2. FM signal Trainer kit

3. Sprectrum analyser

4. CRO (30 MHz)

5. Digital Multimeter6. Antenna Set Up

7. Antennas (Yagi-Uda, Dipole

8. Milli Ammeter (0-10 mA)


Marks



both external and internal and 40% marks in total


42/52

BICSL-018: LabX (Basic Java & UML)

List of Assignments for Java Lab : (Any 8 )

1. Write a Java program that prints all real solutions to the quadratic equation ax2 + bx + c = 0.Read in a, b, c and use the quadratic formula. If the discriminant b2 -4ac is negative, display

a message stating that there are no real solutions.

2. The Fibonacci sequence is defined by the following rule. The first two values in thesequence are 1 and 1. Every subsequent value is the run of the two values preceding it.

Write a Java program that uses both recursive and non recursive functions to print the nth

value in the Fibonacci sequence.

3. Write a Java program that prompts the user for an integer and then prints out all primenumbers up to that Integer.

4. Write a Java program that checks whether a given string is a palindrome or not. Ex:MADAM is a palindrome.

5. Write a Java program for sorting a given list of names in ascending order.6. Write a Java program to multiply two given matrices.7. Write a Java Program that reads a line of integers, and then displays each integers, and the

sum of all the integers (use string to kenizer class)

8. Write a Java program that reads on file name from the user then displays information aboutwhether the file exists, whether the file is readable, whether the file is writable, the type of

file and the length of the file in bytes.9. Write a Java program that reads a file and displays a file and displays the file on the screen,with a line number before each line.

10.Write a Java program that displays the number of characters, lines and words in a text file.

UML Lab:1. The student should take up the case study of Unified Library application which is mentioned

in the theory, and Model it in different views i.e Use case view, logical view, component

view, Deployment view, Database design, forward and Reverse Engineering, and

Generation of documentation of the project.

2. Student has to take up another case study of his/her own interest and do the same what ever

mentioned in first problem. Some of the ideas regarding case studies are given in referencebooks which were mentioned in theory syllabus can be referred for some idea.

Note : The analysis, design, coding, documentation, database design of mini project which will be

carried out in 4th year should be done in object-oriented approach using UML and by using

appropriate

software which supports UML, otherwise the mini project will not be evaluated.


Marks



both external and internal and 40% marks in total


43/52

BICSP- 001 : PROJECT WORK IN SEMESTER V & VI

I n project work group of maximum f ive students wil l work in a team for a common defi ned

objective.

Project work must be done in consultation with the industries and industrial needs. Students

are expected to visit any industry of their liking for selection of industrial projects/problems. They

will prepare document defining the problem clearly. The final draft and scope of project will be

decided by students in consultation with the internal and external (industry expert) guide.

They will train themselves to solve above defined problem if necessary. Once the final draftand scope of project is defined they can work on project with that industry.

Student will complete project work in two phases (two semesters) and they will prepare

presentation of project work carried out in these semesters and present it as Project SeminarI

and I Iin respective semesters. It is expected that students should complete following work as

follows

Semester- V Semester- VI

Visit to industry/ study of a specific problem.

Define a problem.

Finalize the scope and nature of work.

Submit the synopsis.Train themselves (if necessary)

Prepare a rough report containing following

1. Introduction2. Literature survey3. Need and justification of work.

Finalize the report.

Prepare a rough report containing following

4. Experimental work/ testing/design/fabrication.

5. Results6. Discussion7. Conclusions8. Scope of future work.9. References

Finalize the report.

Prepare presentation based on above and present

it as Project SeminarI

Prepare presentation based on total work and

present it as Project SeminarI I

Credit Guidelines

There will be 8 credits assigned to the project work.Oral/ Practical ExaminationIn this, students are expected to prepare for external oral examination. Students will be assessed by

the external examiner which is either appointed by university or by industrial expert (may be called

from industry having work experience in the field in which project is completed). As far as possible,

same external examiner will assess group of students for project in two semesters. This will ensure

involvement of examiner and proper evaluation of project work. The evaluation of the Project is to

be carried out of 200 marks only in sixth semester and no evaluation will be carried out in fifth

semester.


44/52

BICS-036 : VISUAL BASIC PROGRAMMING

UNIT I

Introduction to Visual Basic Environment: Concept of VB program, class, object, property, methods,events, Environment of VB, Concept of project forms etc, Managing with menus, Drag and Drop operation,Validating and processing user inputs.Data types, Variants, Variables, Constants, Arrays- REDIM statement, Array related functions, Collection,

procedure, functions, Argument passing and return values, Input box and message box, Control flowstatement, Loop statement, Nested control structure, Exit statement, Operators-arithmetic, logical, relational,string, FunctionsString, Maths, Date and Time, Date and time formats.Design form to demonstrate: Control loops (do, for, while), Control statements (ifthen, if-then else,

Selection option), Using text box, Command button, Label, options, combo box, input and message box.

UNIT IIControls and Events, Module, Class Module MDI, Menu Editor and Graphics: Scroll bar, Slider,Container- Picture box, frame, Image, file system controls-drive, file, directory list box, Timer control, OLEcontrol, Basic controls like-line, shape, circle, PSet, RGB, Paint picture, load picture.Concept of module, class module, MDI, DLLS and how to use them, Creating own menu using menu editor,Popup menu,Advanced controls: Common dialog box, Tree view, List view, rich text box control, windows commoncontrols, status bar, tab control, image list, MS chart.Concepts of class module, module MDI, DLL and how to use them Using RTF control

UNIT IIIDatabase, Report Generator: Concept of database, record, record set, connection DSN and DSN less

connection, Data Manager. Programming with ADO, DAO, RDO, Object, Connection, record set, parameter,Cursor types, lock types. Creating report using Data Report.

UNIT IV

Introduction to Active X Controls: The user control object-initialize Event, Terminate event, Initproperties Event , paint/Resize Event, Observing the events in the Data controls, Exploring the properties ofActive X controls-Debugging the Properties, Extend properties, Ambient Properties, creating Designed time

only properties, creating a Clock control, Events in Active X control, Using the active X control interfacewizard-Adding the wizard to visual basic, Property pages-using the property page wizard, creating property

pages without the wizard, creating a simple active X control

UNIT V

File Handling in VB: File commands, file handling functions, Sequential files, Reading information from afile, Adding to an existing file, General Sequential files, Sending special characters to sequential files,

Making changes inside a seque