prefabricate din beton armat și precomprimat reinforced...
Post on 07-Feb-2018
308 Views
Preview:
TRANSCRIPT
b
a
c
3%
peste 500 structuri prefabricatepeste 300.000 m3 de beton prefabricat
peste 3.000.000 m2 construiţi
over 500 precast structuresover 300,000 m3 precast concrete
over 3,000,000 m2 built
Prefabricate din beton armat și precomprimat Reinforced and prestressed concrete elements
3
Prezentarea companiei / About the company
ISTORICASA CONS ROMÂNIA SRL a luat fiinţă în anul 1999 ca parte a Grupului ASA Kft. Ungaria, devenind în scurt timp liderul pieţei româneşti în domeniul prefabricatelor din beton armat pen-tru construcţii nerezidenţiale. În decursul anilor ASA CONS a acumulat o experienţă considerabilă în construcţia de centre comerciale şi logistice, depozite, lucrări de infrastructură, con-strucţii industriale şi civile.
În 2008 ASA CONS devine parte a Grupului Consolis, lider eu-ropean în livrarea soluţiilor în domeniul construcţiilor, lucră-rilor civile şi infrastructurii feroviare, specializat în producţia elementelor din beton cu performanţe înalte. Cu aproximativ 10.000 de angajați care operează în 30 de țări din întreaga lume, în special în Europa şi regiunea mediteraneană, Grupul a generat venituri de 1,3 miliarde Euro în 2013. Inovaţia are un rol central în activitatea Consolis. Grupul dezvoltă conti-nuu materiale, produse şi procese de producţie inovatoare cu scopul îmbunătăţirii eficienţei şi calităţii. Cu peste 100 de ani de experienţă, Grupul Consolis a devenit sinonim cu soluţiile inovatoare de ultimă generaţie.
Intrarea în Consolis a însemnat pentru ASA CONS un pas mare spre viitor, acces la tehnologii de vârf şi o infuzie de know-how de la cei mai buni specialişti în domeniu.
EVOLUŢIA ÎN CIFRE/INVESTIŢIICreşterea investiţiilor în domeniu, precum şi dotările cu utilaje şi echipamente moderne, au dus la creşterea producţiei şi a capacităţii de montaj. În 2008 acestea au atins cifre record: 40.000 m3 de beton prefabricat, iar cifra de afaceri a depăşit 40 milioane Euro. Până în prezent, ASA CONS a executat peste 500 structuri prefabricate pentru construcţii civile şi indus-triale, care însumează peste 300.000 m3 de beton prefabri-cat, echivalând aproximativ 3.000.000 m2 construiţi.
ASIGURAREA CALITĂŢIICalitatea materialelor şi a produselor finite este o preocupare permanentă a companiei. Se verifică în permanenţă calitatea betoanelor puse în operă la realizarea elementelor prefabri-cate. Elementele prefabricate executate au certificate de con-formitate, obţinute în urma testelor realizate în laboratorul propriu, laborator de grad II, dotat cu aparatură necesară efec-tuării acestor încercări.
HISTORYASA CONS ROMANIA SRL was founded in 1999 as part of the group ASA Kft. Hungary and has quickly become the market leader in precast concrete for non residential buildings in Ro-mania. ASA CONS built an impressive track record over the years, including commercial and logistic centers, warehouses, infrastructure, civil and industrial buildings.
In 2008 ASA CONS became part of Consolis Group, a leading European Group in building solutions, civil works and rail in-frastructure, specialized in manufacturing high-performance concrete building elements. With around 10,000 employees operating in 30 countries throughout the world, mostly in Eu-rope and the Mediterranean region, the Group generated €1.3 billion in revenue in 2013. Innovation plays a central role in Consolis’ activities. The Group is continually developing new and innovative materials, products and manufacturing pro-cesses in order to improve productivity and quality. With over 100 years of experience Consolis Group has become synony-mous with latest generation innovative solutions.
Joining Consolis Group meant for ASA CONS a big step in the future, access to cutting-edge technology and know-how infu-sion from the best specialists in the field.
FACTS AND FIGURES/INVESTMENTSThe company has consistently made investments in its equip-ment, leading to an increased production and assembly ca-pacity. In 2008, record numbers were achieved: 40,000 m3 of precast concrete and an annual turnover of over 40 million. To date, ASA CONS has produced over 500 precast structures for civil and industrial projects, totalling more than 300,000 m3 of precast concrete, for a total of about 3,000,000 m2 built.
QUALITY ASSURANCEThe quality of materials and finished products is an ongoing priority for the company, who is constantly assessing the qual-ity of the concrete used for precast elements. The precast el-ements hold certificates of compliance, obtained from tests conducted in our Grade II laboratory, well equipped for such tests. ASA CONS’s management is focused on the quality of products and services, aiming daily to exceed the standards to which the
Anul înfiinţării / Founding year: 1999 Intrarea în Consolis / Joined Consolis: 2008
4
company is certified: ISO 9001:2008 for quality, ISO 14001: 2004 for environment and OHSAS 18001: 2007 for health and safety.
GRADE 2 LABORATORY
ASA CONS’s grade 2 laboratory is authorized by State Inspec-torate in Constructions and functions under reference standard SR EN ISO / IEC 17025. The laboratory is equipped with all necessary equipment and follows environmental conditions specified in European standards. This certification authorizes us to conduct determinations both for own products, as well as for third parties, for the following profiles:
1. BBABP – Concrete, reinforced and prestressed concrete• Making concrete specimens • Preservation samples - tests for hardened concrete • Bulk density - tests for hardened concrete • Bulk density of fresh concrete granularity aggregates con-
tained in the concrete mix • Preliminary tests • Workability (consistency) • Compressive strength - tests for hardened concrete • Temperature - tests for fresh concrete • Setting time - fresh concrete testing
2. M.B.M. – Materials for concrete and mortar• The appearance and shape of granules - tests for natural
river aggregates• Humus content • Grading curve. Grading analysis by sieve tests• Dry and wet bulk density • Determination of bulk density. Tests for aggregates
Prezentarea companiei / About the company
Managementul ASA CONS acordă o atenţie deosebită calită-ţii produselor şi serviciilor oferite, urmărind zilnic depăşirea standardelor asumate prin certificarea sistemelor de manage-ment al calităţii ISO 9001:2008, de mediu ISO 14001: 2004 şi al sănătăţii şi securităţii în muncă OHSAS 18001:2007.
LABORATOR DE GRAD II
Laboratorul de gradul II al ASA CONS este autorizat de către Inspectoratul de Stat în Construcţii şi funcţionează conform standardului de referinţă SR EN ISO/CEI 17025, fiind dotat cu echipamentele necesare şi respectând condiţiile de mediu pre-cizate în standardele europene. Această certificare ne autori-zează să efectuăm determinări atât pentru propriile produse, cât şi pentru terţi, pentru următoarele profile:
1. BBABP – beton, beton armat şi beton precomprimat• Confecţionare epruvete beton• Conservare probe – încercări pentru beton întărit• Densitate aparentă - încercări pentru beton întărit• Densitate aparentă a betoanelor în stare proaspătă• Granulozitatea agregatelor conţinute în amestecul de beton• Încercări preliminare• Lucrabilitatea (consistenţa)• Rezistenţa la compresiune – încercări pentru beton întărit• Temperatura – încercări pentru beton proaspăt• Timp de priză – încercări pentru beton proaspăt
2. M.B.M. – Materiale pentru betoane şi mortare • Aspectul şi forma granulelor – încercări pentru agregate na-
turale, de râu• Conţinut de humus• Curba granulometrică. Analiza granulometrică prin cernere• Densitatea în grămadă în stare uscată şi în stare de umidi-
tate naturală
5
• Additive solution density• Floating particles in aggregates• Cements strength: 2 days, 7 days, 28 days • Cement stability (volume constant). Tests for cement • Conservation status - tests for cement • Setting time for cement • Aggregates humidity• Average values b/a and c/a of granules with dmin> 7.1 mm • Organoleptic testing
The testing are performed to improve the quality of services, in accordance with documented procedures and requirements set by our customers. No deviations are accepted and preven-tive measures are taken to eliminate non-quality, along the identification and registration of all non-compliances related to quality and achievement of corrective and preventive ac-tions.
Processes covered:• Collecting• Preservation of samples• Identifying samples• Sampling• Technical process procedures - specific to each type of test• Registration
Advantages of grade 2 laboratory ASA CONS: • Professional and experienced staff, licensed by the Inspec-
torate State in Construction • Tests performed according to European standards • Certificate issuance, recognized in the field as the test report • Develop cumulative bulletin paper • Preparation and verification of concrete recipes • Specialized technical assistance for improving recipes
COMPLETE SERVICESASA CONS is a one-stop-shop partner, supplier of high qual-ity products and customized services. The company offers a variety of products for precast concrete structures: foundation elements, intermediate floor elements, precast roof, wall pan-els and columns, as well as infrastructure solutions: beams, culvert elements, soundproof panels.
• Determinarea masei volumice în vrac. Încercări pentru agre-gate
• Densitatea soluţiei de aditivi• Părţi levigabile din agregate• Rezistenţe mecanice la cimenturi: la 2 zile, 7 zile, 28 zile• Stabilitatea cimentului (constanţă de volum). Încercări pen-
tru ciment• Starea de conservare – încercări pentru ciment• Timpul de priză al cimentului• Umiditatea agregatelor• Valori medii b/a şi c/a ale granulelor cu dmin> 7.1 mm• Verificarea organoleptică
Încercările sunt efectuate cu scopul îmbunătăţirii calităţii serviciilor, conform procedurilor documentate stabilite şi ce-rinţelor clienţilor, neadmiţându-se abateri de la acestea şi lu-ându-se măsuri pentru prevenirea non-calităţii, identificarea şi înregistrarea tuturor neconformităţilor referitoare la calitate şi realizarea acţiunilor corective şi preventive.
Procese reglementate:• Recoltare• Păstrarea probelor• Identificarea probelor• Eşantionare• Proceduri Tehnice de Proces – specifice pentru fiecare tip
de încercări• Înregistrare
Avantajele laboratorului de grad II ASA CONS:• Personal de specialitate, cu experienţă, autorizat de Inspec-
toratul de Stat în Construcţii• Încercări efectuate conform standardelor europene• Emiterea documentelor de atestare, recunoscute în dome-
niu, sub forma raportului de încercare• Elaborarea buletinelor cumulative pe lucrare• Întocmirea şi verificarea reţetelor de beton• Asistenţă tehnică de specialitate pentru îmbunătăţirea re-
ţetelor
SERVICII COMPLETEASA CONS este un partener complet, un furnizor de produse calitative şi servicii adaptate cererilor fiecărui client. Compania vă oferă pentru structurile prefabricate din beton armat: ele-mente de fundare, elemente de planşeu intermediar, elemente prefabricate de acoperiş, panouri şi stâlpi, precum şi soluţii în infrastructură: grinzi de pod, elemente de podeţe, panouri fo-noabsorbante.
Prezentarea companiei / About the company
6
ASA CONS produce gama completă de elemente din beton armat şi precomprimat, oferind în acelaşi timp şi servicii-le adiacente pe care le implică ridicarea unei structuri, de la centre comerciale sau logistice la construcţii industriale sau poduri.
AVANTAJELE PRODUSELOR ASA CONS:- toate produsele noastre respectă întru totul standardele şi
legislaţia în domeniu privind: rezistenţa în timp, rezistenţa la foc, rezistenţa la factorii de mediu
- încorporează materie primă de cea mai bună calitate şi teh-nologie performantă
- fabricarea elementelor presupune o serie de procese riguros definite astfel încât produsul finit va corespunde celor mai mari pretenţii de calitate
- elementele prefabricate executate sunt verificate în laborato-rul propriu; în urma acestei verificări se emite certificatul de conformitate al produsului
AVANTAJELE CLIENŢILOR ASA CONS:- one stop shop- garanţia finală a lucrării- timp redus de la proiectare la execuţie şi montaj; posibili-
tatea avansării construcţiei pe timp de iarnă, până la -20°C- costuri mai mici decât o construcţie clasică- evitarea problemelor cu intermediarii, întrucât echipele noas-
tre de montaj pun în operă elemente deja cunoscute, produse conform aceloraşi standarde de calitate, în mod tradiţional
PROIECTAREPrimul pas în crearea elementelor prefabricate îl reprezintă proiectarea corectă a acestora. Echipa de proiectanţi preia in-formaţiile de la beneficiarul final şi le transformă în planuri concrete, astfel încât produsul finit să corespundă pe deplin nevoilor clienţilor noştri. Această echipă include profesionişti cu experienţa necesară preîntâmpinării oricăror potenţiale piedici în ridicarea efectivă a structurilor din prefabricate. Pu-nem la dispoziţia beneficiarilor consultanţă de specialitate în domeniu.
ASA CONS manufactures and provides the full range of rein-forced and prestressed concrete elements, as well as the services related to raising a structure, from commercial and distribution centres to industrial buildings and bridges.
ASA CONS PRODUCT BENEFITS:- All our products fully comply with standards and legislation
on: resistance over time, fire resistance, resistance to envi-ronment factors
- Made with high quality raw materials and high technology- The manufacturing process consists of a series of rigorous
steps so the finished product will meet the highest quality requirements
- Precast elements are tested in our laboratory; following this examination a certificate of conformity of the product is is-sued
ASA CONS OFFERS TO ITS CLIENTS:- One stop shop- Final work warranty- Reduced time from design to fabrication and installation, al-
lowing for construction in temperatures as low as -20°C- Lower costs than with a traditional building- No third parties, as our installation teams work with already
known items, produced according to the same standards
DESIGNThe first step in creating precast elements is correct and ac-curate design. The design department takes information from the final beneficiary and turns it into blueprints, so that the finished product fully meets our clients’ needs. The depart-ment includes experienced professionals, able to prevent any potential obstacles in the effective elevation of precast structures. We also provide specialized consulting for our customers.
Oferta companiei / Company offer
Soluţii complete marca ASA CONS Complete solutions by ASA CONS
7
EXECUTIONThe company can produce precast elements needed for the fast elevation of slender structures with large span, with a maximum post-to-post distance of 36 m. Up to now, 300,000 m3 of precast concrete left our factory for sites across the country, for a total of about 3,000,000 m2 built.
LOGISTICSASA CONS provides adequate transport for normal and over-sized elements, including columns and beams with a length of 26 or 30 m. We partner with 15 transportation companies ex-perienced in the transportation of regular and oversized loads.
For lifting on site, the company is equipped with 70- and 80-ton Liebherr cranes and 80-ton Tadano Faun crane, as well as Manitou erecting platforms.
ASSEMBLYASA CONS has professional installation teams, with extensive experience in the field. ASA CONS has executed over 500 pre-cast structures for civil and industrial construction. The com-pany can manage projects that include the entire structural build - the precast elements as well as the monolithic build.
A common extension of our mandate is bringing the project to the building envelope, inclusive of enclosures. At times, we have acted as the general contractor for the entire project, as it has been the case of the pharmaceutical center Richter Gedeon in Targu Mures.
EXECUŢIEASA CONS are capacitatea de a produce elementele prefabrica-te necesare ridicării în scurt timp de structuri zvelte, cu deschi-dere mare, permiţând o distanţă maximă între stâlpi de până la 36 m. Până în prezent 300.000 m3 de beton prefabricat au ieşit pe poarta fabricii spre şantiere din întreaga ţară, echiva-lând aproximativ 3.000.000 m2 construiţi.
LOGISTICAASA CONS asigură printr-o logistică adecvată transportul ele-mentelor cu dimensiuni normale şi gabarit depăşit, inclusiv stâlpi şi grinzi cu lungimea de 26 sau 30 m, având un porto-foliu tradiţional de 15 companii cu care colaborează, fiecare specializată în transportul elementelor normale şi cu gabarit depăşit. Pentru ridicarea on site, compania are în dotare auto-macarale tip LIEBHERR de 70 şi 80 tone şi tip TADANO FAUN cu capacitatea de 80 tone, precum şi platforme autoridicătoare MANITOU.
MONTAJASA CONS dispune de echipe de montaj formate din profe-sionişti cu o experienţă vastă în domeniu. Până acum, ASA CONS a executat peste 500 de structuri prefabricate pentru construcţii civile şi industriale. De asemenea, echipele coor-donează şi lucrări care duc la realizarea clădirii în concept de “structură la roşu”, respectiv întreaga structură de rezistenţă, atât componentele prefabricate, cât şi structura monolită.
O extindere uzuală o reprezintă realizarea clădirii la nivel de anvelopă, inclusiv închideri, uneori extinzându-ne competen-ţele până la asigurarea antreprizei generale a unei construc-ţii, ca exemplu execuţia centrului farmaceutic Richter Gedeon Târgu Mureş.
Oferta companiei / Company offer
8
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Armonia - 2 magazine / 2 stores
Baumax - 5 magazine / 5 stores
Anul construcţiei / Construction year: 2007-2008Suprafaţa totală / Total area: 90 000 m2
Anul construcţiei / Construction year: 2006-2011Suprafaţa totală / Total area: 58 000 m2
9
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Anul construcţiei / Construction year: 2004-2011Suprafaţa totală / Total area: 160 000 m2
Cora - 4 magazine / 4 stores
Dedeman - 22 magazine / 22 stores
Anul construcţiei / Construction year: 2006-2014Suprafaţa totală / Total area: 300 000 m2
10
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Jupiter Piteşti
Anul construcţiei / Construction year: 2008Suprafaţa / Area: 55 000 m2
Anul construcţiei / Construction year: 2008-2009Suprafaţa / Area: 61 000 m2
Era Shopping Park Oradea
11
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Anul construcţiei / Construction year: 2005-2014Suprafaţa totală / Total area: 220 000 m2
Kaufland - 27 magazine / 27 stores
Kika Bucureşti
Anul construcţiei / Construction year: 2008Suprafaţa / Area: 27 000 m2
12
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Obi Sibiu
Anul construcţiei / Construction year: 2010Suprafaţa / Area: 10 000 m2
Anul construcţiei / Construction year: 1999-2006Suprafaţa totală / Total area: 220 000 m2
Metro Cash & Carry - 19 magazine / 19 stores
13
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Anul construcţiei / Construction year: 2009-2014Suprafaţa totală / Total area: 32 000 m2
Anul construcţiei / Construction year: 2006Suprafaţa / Area: 86 000 m2
Penny Market - 22 magazine / 22 stores
Polus Cluj-Napoca
14
Lucrări de referinţă - centre comerciale / Reference works - commercial centers
Anul construcţiei / Construction year: 2006-2008Suprafaţa totală / Total area: 77 000 m2
Real Hypermarket - 5 magazine / 5 stores
Praktiker - 5 magazine / 5 stores
Anul construcţiei / Construction year: 2003-2008Suprafaţa totală / Total area: 70 000 m2
15
Lucrări de referinţă - centre comerciale, construcţii industriale / Reference works - commercial centers, industrial buildings
Anul construcţiei / Construction year: 2006-2013Suprafaţa / Area: 47 000 m2
Bosch Blaj
Centru Comercial Târgu Jiu
Anul construcţiei / Construction year: 2013-2014 Suprafaţa / Area: 31 000 m2
16
Lucrări de referinţă - construcţii industriale / Reference works - industrial buildings
Anul construcţiei / Construction year: 2000Suprafaţa / Area: 165 000 m2
Continental Timişoara
Calsonic Kansei Ploieşti
Anul construcţiei / Construction year: 2007 Suprafaţa / Area: 19 000 m2
17
Lucrări de referinţă - construcţii industriale / Reference works - industrial buildings
Anul construcţiei / Construction year: 2008-2013Suprafaţa totală / Total area: 55 000 m2
Emerson Cluj - 5 fabrici / 5 factories
Egger Rădăuţi
Anul construcţiei / Construction year: 2007-2013 Suprafaţa / Area: 70 000 m2
18
Lucrări de referinţă - construcţii industriale / Reference works - industrial buildings
Holzindustrie Schweighoffer Baco Comăneşti
Anul construcţiei / Construction year: 2010-2011Suprafaţa / Area: 45 000 m2
Anul construcţiei / Construction year: 2013Suprafaţa totală / Total area: 16 000 m2
Emerson Oradea - 1 fabrică / 1 factory
19
Lucrări de referinţă - construcţii industriale / Reference works - industrial buildings
Ina Schaeffler Braşov
Anul construcţiei / Construction year: 2003-2008 Suprafaţa / Area: 100 000 m2
Anul construcţiei / Construction year: 2012Suprafaţa / Area: 7 000 m2
Huf Arad - hală producţie / production hall
20
Lucrări de referinţă - construcţii industriale / Reference works - industrial buildings
Makita Brăneşti - 3 fabrici / 3 factories
Anul construcţiei / Construction year: 2007-2013Suprafaţa totală / Total area: 55 000 m2
Anul construcţiei / Construction year: 2008Suprafaţa / Area: 40 000 m2
Kronospan Braşov
21
Anul construcţiei / Construction year: 2012-2013Suprafaţa / Area: 28 000 m2
Plexus Oradea
Anul construcţiei / Construction year: 2012Suprafaţa / Area: 8 000 m2
MGI Coutier Ghiroda
Lucrări de referinţă - construcţii industriale / Reference works - industrial buildings
22
Lucrări de referinţă - depozite logistice / Reference works - logistic warehouses
Aramis Baia Mare
Anul construcţiei / Construction year: 2014Suprafaţa / Area: 37 500 m2
Bucharest West Logistic Park
Anul construcţiei / Construction year: 2008 Suprafaţa / Area: 7 000 m2
23
Lucrări de referinţă - depozite logistice / Reference works - logistic warehouses
Gedeon Richter Târgu-Mureş
Anul construcţiei / Construction year: 2007 Suprafaţa / Area: 13 000 m2
Anul construcţiei / Construction year: 2009Suprafaţa / Area: 70 000 m2
Dacia Renault Piteşti
24
Lucrări de referinţă - depozite logistice / Reference works - logistic warehouses
Log Center - 2 depozite / 2 warehouses
Anul construcţiei / Construction year: 2007-2008 Suprafaţa totală / Total area: 35 000 m2
Anul construcţiei / Construction year: 2011Suprafaţa / Area: 46 000 m2
Lidl Iernut
25
Lucrări de referinţă - depozite logistice, construcţii civile / Reference works - logistic warehouses, civil buildings
Ansamblu rezidenţial Sibiu / Residential buildings Sibiu
Anul construcţiei / Construction year: 2014 Suprafaţa / Area: 630 m2
Rewe Turda
Anul construcţiei / Construction year: 2007-2012 Suprafaţa / Area: 24 000 m2
26
Ansamblu rezidenţial Cluj-Napoca / Residential buildings Cluj-Napoca
Anul construcţiei / Construction year: 2014-2015 Suprafaţa / Area: 16 000 m2
Lucrări de referinţă - construcţii civile / Reference works - civil buildings
Piaţa agroalimentară Rogerius Oradea / Rogerius marketplace Oradea
Anul construcţiei / Construction year: 2014-2015 Suprafaţa / Area: 8 000 m2
27
Lucrări de referinţă - lucrări infrastructură / Reference works - infrastructure works
Anul construcţiei / Construction year: 2007
Pasaj Iulius Mall / Iulius Mall passage Cluj-Napoca
Pasaj Polus Center / Polus Center passage Cluj-Napoca
Anul construcţiei / Construction year: 2007
28
Lucrări de referinţă - lucrări infrastructură / Reference works - infrastructure works
Anul construcţiei / Construction year: 2013
Pod Sânpaul / Sanpaul bridge
Poduri peste râul Someş / Bridges over river Somes
Anul construcţiei / Construction year: 2008
29
Anul construcţiei / Construction year: 2009
Şoseaua de centură / Beltway Cluj-Napoca
Autostrada Transilvania / Transilvania highway
Anul construcţiei / Construction year: 2009-2010
Lucrări de referinţă - lucrări infrastructură / Reference works - infrastructure works
30
Lucrări de referinţă / Reference works
ASA CONS ROMÂNIA SRLStr. 22 Decembrie 1989 nr. 27401113 Turda · RomâniaTel. +40 264 312 765 · Fax +40 264 317 057 contact@asacons.ro · www.asacons.ro · www.consolis.ro
peste 500 structuri prefabricatepeste 300.000 m3 de beton prefabricat
peste 3.000.000 m2 construiţi
over 500 precast structuresover 300,000 m3 precast concrete
over 3,000,000 m2 built
Prefabricate din beton armat și precomprimat Reinforced and prestressed concrete elements
Construcţii industriale - produseIndustrial buildings - products
31
32
Produse - Elemente de fundare / Products - Foundation elements
Pahare / Pocket foundations
Din structura fundaţiei pahar se execută prefabricat gulerul, care transportat în şantier se roteşte cu 180° în plan vertical, după care se leagă pe mustăţi armătura tălpii paharului şi se montează pe poziţie.Eliminând manopera în şantier şi timpul de maturizare a betonului, viteza de montaj a structurii creşte considerabil.
From the structure of the pocket foundation the collar is precast executed; on site it is vertically rotated by 180 degrees, then the plate reinforcement is con-nected on stubs and assembled in position.By eliminating labor on site and concrete maturation time, the erection speed of the structure rises considerably.
Vedere 3D / 3D view
33
Produse - Elemente de fundare / Products - Foundation elements
Nr. crt. a b e h
1 0.90 0.90 0.25 1.10
2 1.20 1.20 0.25 1.10
3 1.30 1.30 0.25 1.10
4 1.50 1.50 0.30 1.10
5 1.50 2.30 0.30 1.10
6 1.60 2.60 0.30 1.10
1 - egalizare2 - talpă monolită 3 - pahar prefabricat
1 - equalization2 - monolithic base3 - precast pocket foundation
Dimensiuni / Dimensions
Secţiune caracteristică / Specific section
34
Produse - Stâlpi / Products - Columns
Stâlpi / Columns
Lungimile stâlpilor variază între 5 şi 24 m. / The column length varies between 5 and 24 m.
Stâlpii prefabricaţi sunt executaţi într-o varietate de dimensiuni, forme şi lun-gimi. Suprafaţa betonului este netedă, iar muchiile sunt teşite. În general stâl-pii necesită o secţiune transversală minimă de 300 x 300 mm, care asigură o bună conexiune cu grinzile, o manipulare uşoară, precum şi o rezistenţă la foc de 120 minute făcându-i potriviţi pentru o gamă largă de construcţii. The columns are made in a variety of dimensions, shapes and lengths. The surface of the concrete is smooth and the edges are beveled. Generally the columns require a minimum cross section of 300 x 300 mm that ensures a good connection with the beams, an easy handling and a 120 minutes fire resistance, making them suitable for a large range of construction.
Vedere 3D / 3D view
35
a
b
Produse - Stâlpi / Products - Columns
Nr. crt. a b
1 0.25 0.25
2 0.40 0.40
3 0.50 0.50
4 0.54 0.60
5 0.60 0.60
6 0.70 0.70
7 0.80 0.80
8 0.80 1.20
Secţiune caracteristică / Specific section
Dimensiuni / Dimensions
36
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Grinzi “I” drepte / Straight “I” beams
Lungimea poate varia de la 12 la 27 m. / Lenght can vary between 12 and 27 m.
Vedere 3D / 3D view
Grinzile principale se execută cu secţiune constantă sau secţiune variabilă funcţie de soluţia de scurgere a apelor de pe acoperiş. La rândul lor ambele tipuri pot avea secţiunea transversală I sau T funcţie de deschiderea halei şi încărcările la nivelul acoperişului, iar îmbinarea acestora cu stâlpii structurii este de tip uscat.
The main beams are executed with constant or variable section depending on the solution of draining water of the roof. Both types can have I or T cross section depending on the hall’s opening and loads at the roof level. The con-nection with the structure’s columns is made by dry mechanical fixing.
37
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Capăt / End Coamă / Ridge
Secţiuni caracteristice / Specific sections
Vedere laterală / Side view
38
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Grinzi 30 m “I” în două ape / 30 m “I” beams
Lungimea poate varia de la 12 la 30 m. / Lenght can vary between 12 and 30 m.
Vedere 3D / 3D view
Grinzile principale se execută cu secţiune constantă sau secţiune variabilă funcţie de soluţia de scurgere a apelor de pe acoperiş. La rândul lor ambele tipuri pot avea secţiunea transversală I sau T funcţie de deschiderea halei şi încărcările la nivelul acoperişului, iar îmbinarea acestora cu stâlpii structurii este de tip uscat.
The main beams are executed with constant or variable section depending on the solution of draining water of the roof. Both types can have I or T cross section depending on the hall’s opening and loads at the roof level. The con-nection with the structure’s columns is made by dry mechanical fixing.
39
15
97205 2
15
30
60
119
60
30
135858
523 523
90205 3
145
235 8
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Pantă 3% / Slope 3%Pantă 3% / Slope 3%
Capăt / End Coamă / Ridge
Secţiuni caracteristice / Specific sections
Vedere laterală / Side view
40
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Grinzi “T” drepte / Straight “T” beams
Lungimea poate varia de la 12 la 27 m. / Lenght can vary between 12 and 27 m.
Vedere 3D / 3D view
Grinzile principale se execută cu secţiune constantă sau secţiune variabilă funcţie de soluţia de scurgere a apelor de pe acoperiş. La rândul lor ambele tipuri pot avea secţiunea transversală I sau T funcţie de deschiderea halei şi încărcările la nivelul acoperişului, iar îmbinarea acestora cu stâlpii structurii este de tip uscat.
The main beams are executed with constant or variable section depending on the solution of draining water of the roof. Both types can have I or T cross section depending on the hall’s opening and loads at the roof level. The con-nection with the structure’s columns is made by dry mechanical fixing.
41
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Nr. crt. a
1 0.18
2 0.20
3 0.23
Dimensiuni / Dimensions
Vedere laterală / Side view
Secţiune caracteristică / Specific section
42
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Grinzi “T” în două ape / “T” beams
Lungimea poate varia de la 12 la 24 m. / Lenght can vary between 12 and 24 m.
Vedere 3D / 3D view
Grinzile principale se execută cu secţiune constantă sau secţiune variabilă funcţie de soluţia de scurgere a apelor de pe acoperiş. La rândul lor ambele tipuri pot avea secţiunea transversală I sau T funcţie de deschiderea halei şi încărcările la nivelul acoperişului, iar îmbinarea acestora cu stâlpii structurii este de tip uscat.
The main beams are executed with constant or variable section depending on the solution of draining water of the roof. Both types can have I or T cross section depending on the hall’s opening and loads at the roof level. The con-nection with the structure’s columns is made by dry mechanical fixing.
43
105
Pantă 3% / Slope 3% Pantă 3% / Slope 3%
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Secţiuni caracteristice / Specific sections
Capăt / End Coamă / Ridge
Vedere laterală / Side view
44
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Pane secţiune “T” / “T” section purlins
Panele se execută în special în variantă precomprimată cu secţiuni trapezoi-dale sau T. Lungimea lor şi îmbinarea cu restul structurii se stabileşte în parte pentru fiecare structură.
Purlins can be made also prestressed with trapezoidal or T section. The length and the connection with the rest of the structure are determined separately for each structure.
Vedere 3D / 3D view
Lungimea poate varia de la 6 la 24 m. / Lenght can vary between 6 and 24 m.
45
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
a b c d
0.30-0.50 0.14-0.20 0.31-0.61 0.10-0.30
Dimensiuni / Dimensions
Vedere laterală / Side view
Secţiune caracteristică / Specific section
46
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Pane trapez / Trapezoidal purlins
Vedere 3D / 3D view
Lungimea poate varia de la 6 la 24 m. / Lenght can vary between 6 and 24 m.
Panele se execută în special în variantă precomprimată cu secţiuni trapezoi-dale sau T. Lungimea lor şi îmbinarea cu restul structurii se stabileşte în parte pentru fiecare structură.
Purlins can be made also prestressed with trapezoidal or T section. The length and the connection with the rest of the structure are determined separately for each structure.
47
Produse - Elemente prefabricate de acoperiş / Products - Roof precast elements
Secţiuni caracteristice / Specific sections
Vedere laterală / Side view
48
Lungimea poate varia de la 6 la 15 m. / Lenght can vary between 6 and 15 m.
Grinzile de planşeu servesc ca suport pentru plăcile constituen-te ale planşeului. Pe aceste elemente se pot rezema fâşii cu go-luri, predale şi alte elemente de planşeu. Prin alcătuirea acestor ele-mente se poate asigura continuarea pe reazeme în suprabetonare. Floor beams are used as support for constituent slabs of the floor. On these elements hollow core slabs, filigrames and other floor elements can be rest. Using floor beams, bearings extension in over concreting can be assured.
Vedere 3D / 3D view
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Grinzi de planşeu / Floor beams
49
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
a b
0.40-0.80 0.40-0.80
Secţiune caracteristică / Specific section
Dimensiuni / Dimensions
Vedere laterală / Side view
a
b
50
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Elemente TT / TT elements
Lungimea poate varia de la 6 la 17 m. / Lenght can vary between 6 and 17 m.
Acest tip de elemente se foloseşte pentru planşee încărcate cu sarcini mari până la deschideri de 17 m. Capacitatea portantă a acestora se proiectează după necesităţi prin dimensionarea suprabetonării. Variaţia dimensionărilor se poate asigura prin lăţimea plăcii laterale, respectiv înălţimea şi lăţimea nervurilor.
This type of elements are used for slabs loaded with high loads up to 17 m spans. Their bearing capacity is designed according to requirements by dimen-sioning of the over concreting. The variation of the correct dimensioning can be assured by the width of side slab, respectively height and width of the ribs.
Vedere 3D / 3D view
51
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Secţiune caracteristică / Specific section
Vedere laterală / Side view
52
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Fâşii cu goluri - FGP 200 / Hollow core slabs - FGP 200
Aceste produse sunt executate cu tehnologie de beton extrudat pe piste continue de 90 m cu debitare la lungime după necesităţile proiectantului. Sunt executate din beton C50/60 şi cu armare exclusiv cu toroane după o conformare rezulta-tă din dimensionare. Înălţimea secţiunilor produse la ASA sunt de 20 şi 32 cm. These products are executed with extruded concrete technology on 90 m con-tinuous tracks with cut to length according to designer’s needs. They are ex-ecuted of C50/60 concrete with reinforcing exclusively with strands according to a sizing calculation. Sections produced at ASA CONS are of 20 and 32 cm.
Vedere 3D / 3D view
53
Încă
rcăr
i adm
ise,
val
ori c
arac
teris
tice
Perm
issib
le lo
ad, c
hara
cter
istic
valu
es
[daN
/m2 ]
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Secţiune caracteristică / Specific section
H(mm)
I(mm)
TIP
Cod produs
Numărtoroane
Diametru toron (mm)
200 1200
FGP-200/A 69.3
FGP-200/B 8
FGP-200/C 612.9
FGP-200/D 8
toro
ane
stra
nds
toroane strands
(section area) (volume/meter) (weight/meter) (point/meter)(total weight) (density/m3)
Deschidere Opening
54
Fâşii cu goluri - FGP 320 / Hollow core slabs - FGP 320
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Vedere 3D / 3D view
Aceste produse sunt executate cu tehnologie de beton extrudat pe piste continue de 90 m cu debitare la lungime după necesităţile proiectantului. Sunt executate din beton C50/60 şi cu armare exclusiv cu toroane după o conformare rezulta-tă din dimensionare. Înălţimea secţiunilor produse la ASA sunt de 20 şi 32 cm. These products are executed with extruded concrete technology on 90 m con-tinuous tracks with cut to length according to designer’s needs. They are ex-ecuted of C50/60 concrete with reinforcing exclusively with strands according to a sizing calculation. Sections produced at ASA CONS are of 20 and 32 cm.
55
H(mm)
I(mm)
TIP
Cod produs
Numărtoroane
Diametru toron (mm)
320 1200
FGP-320/A 5+2
12.9FGP-320/B 7+2
FGP-320/C 8+2
FGP-320/D 11+2
Secţiune caracteristică / Specific section
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
toroane strands
toroane strands
5 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
7 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
8 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
11 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
FGP-320/A
FGP-320/B
FGP-320/C
FGP-320/D
volum/metru: V=0.1993 m3/mlmasa/metru: M=478.32 kg/mlrost/metru: m=33.6 kg/ml
densitate/m33: 24.00 kN/m
FGP-320
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
A (7 TBP-12,90) B (9 TBP-12,90)
C (10 TBP-12,90) D (13 TBP-12,90)
6559
90510251280
45510
665765970
31011
485565740
20012
350420565
11513
245305430
14
160210325
15
135235
16
165
(section area) (volume/meter) (weight/meter) (point/meter)(total weight) (density/m3)
Încă
rcăr
i adm
ise,
val
ori c
arac
teris
tice
Perm
issib
le lo
ad, c
hara
cter
istic
valu
es
[daN
/m2 ]
Deschidere Opening
56
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Predale / Filigrames
Vedere 3D / 3D view
Lungimea poate varia de la 2 la 8 m. / Lenght can vary between 2 and 8 m.
Sunt elementele componente pentru planşee la care prin suprabetonare se realizează o structură cu planşeu mixt. Acestea au rol de cofraj şi de obicei trebuie sprijinite pe durata turnării şi maturizării suprabetonării.
These products are component elements for floors whereat by over concreting is achieved a monolith floor. These elements have formwork function and usu-ally must be supported during casting period and over concreting maturation.
57
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Secţiune caracteristică / Specific section
suprafaţă rugoasărough surface
suprafaţă rugoasărough surface
58
Produse - Panouri de faţadă şi grinzi de soclu / Products - Facade panels and cap beams
Vedere 3D / 3D view
Panourile prefabricate pot fi interioare de tip antifoc şi exterioare de tip tristrat. Acestea la rândul lor sunt panouri de soclu şi panouri curente. Di-mensiunile panourilor sunt limitate de posibilitatea manipulării şi trans-portului. Fixarea lor de structură se face cu îmbinări sudate sau înşurubate.
Precast panels can be interiors type fire resistant and exteriors type tri layer which at their turn can be socle panels and current panels. The dimensions of the panel are limited by the possibility of manipulation and transport. The set-ting with the structure is made by screwed or welded joints.
Notă: vezi şi panourile grafice de la pagina 66. Note: see also the graphic panels on page 66.
Panouri de faţadă monostrat şi tristrat - beton aparent / Monolayer and trilayer concrete facade panels - exposed concrete
59
Produse - Panouri de faţadă şi grinzi de soclu / Products - Facade panels and cap beams
Tip/mărime H max L max b1 t b2
Panou tristrat 4.8 m 15 m 12-16 cm 6-8 cm 7-10 cm
Panou monostrat 4.8 m 15 m 12-35 cm - -
Secţiuni caracteristice / Specific sections
Dimensiuni / Dimensions
Vedere laterală / Side view
60
Produse - Trepte prefabricate beton armat / Products - Precast concrete staircase
Vedere 3D / 3D view
Trepte prefabricate beton armat / Precast concrete staircase
Scara prefabricată din beton armat este un element de construcţie care asi-gură legătura pe verticală între diferite etaje ale clădirii. Dintre avantajele prefabricării sistemului de trepte merită menţionate: dimensiunile exacte, forma perfectă şi identică a elementelor proiectate, gama variată de realizare a acestora în funcţie de necesităţile clientului, precum şi reducerea timpului de execuţie pe şantier prin eliminarea timpului necesar realizării cofrajului.
The precast concrete staircase is a construction element that provides vertical connection between different floors of the building. Among the advantages of concrete prefabricating system worth mentioning: size precision, perfect sha-pe and identical elements, designed for a wide range of projects, depending on customer needs and reducing execution time on site by eliminating the time required to complete the shuttering.
61
Produse - Trepte prefabricate beton armat / Products - Precast concrete steps
d
AA
Secţiuni caracteristice / Specific sections
Notă: dimensiunea variază în funcţie de specificul proiectului. / Note: size varies depending on the type of the project.
Vedere laterală / Side view
h
ab
l
62
63
Construcţii civile - produseCivil buildings - products
64
Informaţii utile / Useful information
65
Informaţii utile / Useful information
Analiză comparativă a planşeelor / Concrete slab benchmarking
Avantajele produselor prefabricate / Precast concrete products advantages
Timp de execuţie şi montaj redus, fiind independent de condiţiile meteorologice
Performance and reduced installation time, it does not depend on the weather
Cost redus de execuţie şi montaj Lower costs for manufacturing and assembly
Pot lua orice forme şi dimensiuni Any shape or size
Calitate superioară în producţie, datorită controlului permanent din fabrică
High quality production due to permanent producti-on control
Elementele prefabricate se livrează pe şantier cu cer-tificate de conformitate
Prefabricated elements are delivered on site with compliance certificates
Asigură protecţie termică, fonică, împotriva apei şi a focului
Resistant to most external factors thermal, sound, water, fire
Elementele prefabricate sunt durabile; rezistenţa lor creşte gradual în timp
Prefabricated elements are durable; their resistance gradually increases over time
Utilizare mai buna a spaţiului construit datorită des-chiderilor mari a elementelor prefabricate
Better use of space built through large openings pre-fabricated elements
Indicator / Indicator FGP + suprabetonare / Hollow concrete slab Planşeu monolit / Monolithic slab
lei/m2 lei/m2
Fabricaţie / Production 83
Transport / Transport 15
Preţ montaj / Installation price 27
Macara / Crane inclus da nu
Cofraj / Framework nu 80 manoperă + material
Armare / Reinforcement 22 4kg/m2, ø8/20 91 17kg/m2, 2ø8/10
Folie / Foil nu da
Betonare / Casting 24 8 cm 45 15 cm, manoperă + material
Finisaj / Finishing 11 1 strat tinci nu necesită alte straturi
Grosime / Thickness 25-45 cm 15 cm
Timp / Time 40 m2/h 5 m2/h
Personal / Personnel 4 6
Fono/Termo / Phonic/Thermal da nu
Total costuri / Total costs 182 mai economic şi mai rapid 216
66
Panouri grafice / Graphic panels
Sectorul comercial / Commercial sector
Produse - Panouri grafice / Products - Graphic panels
Panourile grafice sunt un produs prefabricat nou, unicat în România, care oferă plusvaloare proiectelor dumneavoastră. Prin crearea unor suprafeţe tex-turate cu un design original la alegere, acestea vor transforma o simplă con-strucţie într-o operă de artă. Nu există limite în dimensiunea şi tipul designului sau imaginii unice utilizate în crearea texturii panourilor grafice. ASA CONS este singurul producător din România care deţine tehnologia de producţie şi vă poate oferi acest tip de panouri. Ele sunt realizate după o teh-nologie de ultimă generaţie, originară din Finlanda. Metoda utilizată are ca şi rezultat o suprafaţă texturată, netedă sau complet expusă. Textura de pe suprafaţă este rezultatul contrastului dintre faţa panoului şi expunerea finisa-jului agregat. Aceasta este o metodă eficientă din punct de vedere al costurilor, finisajul agregat fiind folosit în faza de producţie a elementelor de beton..
Aplicabilitatea panourilor grafice este similară cu cea a panourilor de faţadă, ele putând fi implementate într-o gamă variată de tipuri de construcţii, de la construcţii civile şi industriale la lucrări de infrastructură, atât pentru exterior, cât şi pentru interior.
Prin utilizarea panourilor grafice veţi obţine o faţadă cu stil la un preţ rezonabil.
Panourile grafice sunt:•Cumultstilşilaunpreţrezonabil•Durabileşiuşordeîntreţinut•Testateşisigure
Panourile grafice înseamnă noi posibilităţi arhitecturale şi o nouă modalitate de finisare a construcţiilor. Singura limită este imaginaţia!
The graphic panels are a new precast product, unique in Romania, providing added value to your projects. By creating textured surfaces with an original design of choice, they will turn a simple design into a work of art. There are no limits on the size and type of design or single image graphic panels used to create texture.
ASA CONS is the only producer in Romania holding production technology and capability to provide this type of facade panels. They are created using cutting-edge technology, originally from Finland. The method used results in a patterned, smooth or completely exposed surface. The pattern on the surface results from the contrast between the fairface and the exposed fine aggregate finish. This is a cost-effective, tested and safe method because traditional ex-posed fine aggregate materials and processes are used in the manufacturing of concrete elements.
The applicability of graphical panels is similar to the facade panels; they can be implemented in a wide range of building types, from civil and industrial buildings to infrastructure works, both for exterior and interior projects.
Graphic concrete offers the chance to produce a stylish facade at a reason-able price.
Graphic concrete is:•Stylishandreasonablypriced•Durableandeasytomaintain•Testedandsafe
Graphic concrete offers new building possibilities and a new way of finishing constructions. Imagination is your only limit!
Produse - Panouri grafice / Products - Graphic panels
Sectorul industrial / Industrial sector
Sectorul rezidenţial / Residential sectorSectorul ambiental / Environmental sector
Sectorul public / Public sector
Produse - Panouri grafice / Products - Graphic panels
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Fâşii cu goluri - FGP 200 / Hollow core slabs - FGP 200
Aceste produse sunt executate cu tehnologie de beton extrudat pe piste continue de 90 m cu debitare la lungime după necesităţile proiectantului. Sunt executate din beton C50/60 şi cu armare exclusiv cu toroane după o conformare rezulta-tă din dimensionare. Înălţimea secţiunilor produse la ASA sunt de 20 şi 32 cm. These products are executed with extruded concrete technology on 90 m con-tinuous tracks with cut to length according to designer’s needs. They are ex-ecuted of C50/60 concrete with reinforcing exclusively with strands according to a sizing calculation. Sections produced at ASA CONS are of 20 and 32 cm.
Vedere 3D / 3D view
6867
69
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Secţiune caracteristică / Specific section
H(mm)
I(mm)
TIP
Cod produs
Numărtoroane
Diametru toron (mm)
200 1200
FGP-200/A 69.3
FGP-200/B 8
FGP-200/C 612.9
FGP-200/D 8
toro
ane
stra
nds
toroane strands
(section area) (volume/meter) (weight/meter) (point/meter)(total weight) (density/m3)
Încă
rcăr
i adm
ise,
val
ori c
arac
teris
tice
Perm
issib
le lo
ad, c
hara
cter
istic
valu
es
[daN
/m2 ]
Deschidere Opening
70
Fâşii cu goluri - FGP 320 / Hollow core slabs - FGP 320
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Vedere 3D / 3D view
Aceste produse sunt executate cu tehnologie de beton extrudat pe piste continue de 90 m cu debitare la lungime după necesităţile proiectantului. Sunt executate din beton C50/60 şi cu armare exclusiv cu toroane după o conformare rezulta-tă din dimensionare. Înălţimea secţiunilor produse la ASA sunt de 20 şi 32 cm. These products are executed with extruded concrete technology on 90 m con-tinuous tracks with cut to length according to designer’s needs. They are ex-ecuted of C50/60 concrete with reinforcing exclusively with strands according to a sizing calculation. Sections produced at ASA CONS are of 20 and 32 cm.
71
H(mm)
I(mm)
TIP
Cod produs
Numărtoroane
Diametru toron (mm)
320 1200
FGP-320/A 5+2
12.9FGP-320/B 7+2
FGP-320/C 8+2
FGP-320/D 11+2
Secţiune caracteristică / Specific section
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
toroane strands
toroane strands
FGP-320
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
A (7 TBP-12,90) B (9 TBP-12,90)
C (10 TBP-12,90) D (13 TBP-12,90)
6559
90510251280
45510
665765970
31011
485565740
20012
350420565
11513
245305430
14
160210325
15
135235
16
165
5 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
7 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
8 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
11 buc TBP 12.9-1860 (Ø12.9)Pk=110 kN
FGP-320/A
FGP-320/B
FGP-320/C
FGP-320/D
volum/metru: V=0.1993 m3/mlmasa/metru: M=478.32 kg/mlrost/metru: m=33.6 kg/ml
densitate/m33: 24.00 kN/m
(section area) (volume/meter) (weight/meter) (point/meter)(total weight) (density/m3)
Încă
rcăr
i adm
ise,
val
ori c
arac
teris
tice
Perm
issib
le lo
ad, c
hara
cter
istic
valu
es
[daN
/m2 ]
Deschidere Opening
72
Vedere 3D / 3D view
Produse - Trepte prefabricate beton armat / Products - Precast concrete staircase
Trepte prefabricate beton armat / Precast concrete staircase
Scara prefabricată din beton armat este un element de construcţie care asi-gură legătura pe verticală între diferite etaje ale clădirii. Dintre avantajele prefabricării sistemului de trepte merită menţionate: dimensiunile exacte, forma perfectă şi identică a elementelor proiectate, gama variată de realizare a acestora în funcţie de necesităţile clientului, precum şi reducerea timpului de execuţie pe şantier prin eliminarea timpului necesar realizării cofrajului.
The precast concrete staircase is a construction element that provides vertical connection between different floors of the building. Among the advantages of concrete prefabricating system worth mentioning: size precision, perfect sha-pe and identical elements, designed for a wide range of projects, depending on customer needs and reducing execution time on site by eliminating the time required to complete the shuttering.
73
Produse - Trepte prefabricate beton armat / Products - Precast concrete steps
d
AA
Secţiuni caracteristice / Specific sections
Vedere laterală / Side view
h
ab
l
Notă: dimensiunea variază în funcţie de specificul proiectului. / Note: size varies depending on the type of the project.
74
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Predale / Filigrames
Vedere 3D / 3D view
Lungimea poate varia de la 2 la 8 m. / Lenght can vary between 2 and 8 m.
Sunt elementele componente pentru planşee la care prin suprabetonare se realizează o structură cu planşeu mixt. Acestea au rol de cofraj şi de obicei trebuie sprijinite pe durata turnării şi maturizării suprabetonării.
These products are component elements for floors whereat by over concreting is achieved a monolith floor. These elements have formwork function and usu-ally must be supported during casting period and over concreting maturation.
75
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Secţiune caracteristică / Specific section
suprafaţă rugoasărough surface
suprafaţă rugoasărough surface
76
Produse - Panouri de faţadă şi grinzi de soclu / Products - Facade panels and cap beams
Panourile prefabricate pot fi interioare de tip antifoc şi exterioare de tip tristrat. Acestea la rândul lor sunt panouri de soclu şi panouri curente. Di-mensiunile panourilor sunt limitate de posibilitatea manipulării şi trans-portului. Fixarea lor de structură se face cu îmbinări sudate sau înşurubate.
Precast panels can be interiors type fire resistant and exteriors type tri layer which at their turn can be socle panels and current panels. The dimensions of the panel are limited by the possibility of manipulation and transport. The set-ting with the structure is made by screwed or welded joints.
Notă: vezi şi panourile grafice de la pagina 66. Note: see also the graphic panels on page 66.
Vedere 3D / 3D view
Panouri de faţadă monostrat şi tristrat - beton aparent / Monolayer and trilayer concrete facade panels - exposed concrete
77
Produse - Panouri de faţadă şi grinzi de soclu / Products - Facade panels and cap beams
Tip/mărime H max L max b1 t b2
Panou tristrat 4.8 m 15 m 12-16 cm 6-8 cm 7-10 cm
Panou monostrat 4.8 m 15 m 12-35 cm - -
Secţiuni caracteristice / Specific sections
Dimensiuni / Dimensions
Vedere laterală / Side view
78
Lungimea poate varia de la 6 la 15 m. / Lenght can vary between 6 and 15 m.
Grinzile de planşeu servesc ca suport pentru plăcile constituen-te ale planşeului. Pe aceste elemente se pot rezema fâşii cu go-luri, predale şi alte elemente de planşeu. Prin alcătuirea acestor ele-mente se poate asigura continuarea pe reazeme în suprabetonare. Floor beams are used as support for constituent slabs of the floor. On these elements hollow core slabs, filigrames and other floor elements can be rest. Using floor beams, bearings extension in over concreting can be assured.
Vedere 3D / 3D view
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Grinzi de planşeu / Floor beams
79
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
a b
0.40-0.80 0.40-0.80
Secţiune caracteristică / Specific section
Dimensiuni / Dimensions
Vedere laterală / Side view
a
b
80
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Elemente TT / TT elements
Acest tip de elemente se foloseşte pentru planşee încărcate cu sarcini mari până la deschideri de 17 m. Capacitatea portantă a acestora se proiectează după necesităţi prin dimensionarea suprabetonării. Variaţia dimensionărilor se poate asigura prin lăţimea plăcii laterale, respectiv înălţimea şi lăţimea nervurilor.
This type of elements are used for slabs loaded with high loads up to 17 m spans. Their bearing capacity is designed according to requirements by dimen-sioning of the over concreting. The variation of the correct dimensioning can be assured by the width of side slab, respectively height and width of the ribs.
Vedere 3D / 3D view
Lungimea poate varia de la 6 la 17 m. / Lenght can vary between 6 and 17 m.
81
Produse - Elemente de planşeu intermediar / Products - Intermediate floor elements
Secţiune caracteristică / Specific section
Vedere laterală / Side view
8282
83
Infrastructură - produseInfrastructure - products
84
Grinzi de pod 42 şi 52 cm / Bridge beams 42 and 52 cm
Produse - Grinzi de pod / Products - Bridge beams
Lungimea poate varia de la 10 la 12 m. / Lenght can vary between 10 and 12 m.
Vedere 3D / 3D view
Grinzile de pod sunt asimilate din gama de produse IPTANA pentru diferite deschideri şi sarcini, cu secţiune I şi T, cu deschideri între 10 şi 12 metri. Pro-dusele fiind de catalog, suportă modificări şi adaptări în limita acceptării aces-tora de către proiectanţi.
Bridge beams are assimilated from the IPTANA products range for various spans and loads, with I and T sections, with spans between 10 and 12 meters. As catalogue products can be modified and adapted in the acceptance limit of the designers.
85
Produse - Grinzi de pod / Products - Bridge beams
Dispunere toroane / Strands layoutSecţiune caracteristică / Specific sectionSecţiune transversală / Cross section
Dimensiuni / Dimensions
L (m)Încărcare admisă
Valoare caracteristică(kN/ml)
6 61
8 36
10 23
L (m)Încărcare admisă
Valoare caracteristică(kN/ml)
10 30
12 19.5
19 1922
5 25 7
702
5
531
52
1
52 60
5
14
5 42
53
5 035 3
5 5 5 5 5 5 5 56 644
60
7 4 4 722
5
7 4 4 722
5 5 5 5 5 5 56 644
60
19 1922
531
52
1
52 60
5 5
5 25 7
702
51
25
53
5 045 3
Grindă de pod 42 / 42 Bridge beam Grindă de pod 52 / 52 Bridge beam
86
Grinzi de pod 72 şi 80 cm / Bridge beams 72 and 80 cm
Lungimea poate varia de la 14 la 18 m. / Lenght can vary between 14 and 18 m.
Vedere 3D / 3D view
Produse - Grinzi de pod / Products - Bridge beams
Grinzile de pod sunt asimilate din gama de produse IPTANA pentru diferite deschideri şi sarcini, cu secţiune I şi T, cu deschideri între 12 şi 18 metri. Pro-dusele fiind de catalog, suportă modificări şi adaptări în limita acceptării aces-tora de către proiectanţi.
Bridge beams are assimilated from the IPTANA products range for various spans and loads, with I and T sections, with spans between 12 and 18 meters. As catalogue products can be modified and adapted in the acceptance limit of the designers.
87
R=5 R=5
92
851 1
25 25
R=5 R=5
Produse - Grinzi de pod / Products - Bridge beams
Dispunere toroane / Strands layoutSecţiune caracteristică / Specific sectionSecţiune transversală / Cross section
Dimensiuni / Dimensions
L (m)Încărcare admisă
Valoare caracteristică(kN/ml)
14 40.5
16 25.5
92
851 1 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
25 25
35 80
58
4882
8525
5
3
35
8
335 335
102 42 429102
9
4 427R=5
R=5
R=5
R=5
Grindă de pod 72 / 72 Bridge beam
88
Produse - Grinzi de pod / Products - Bridge beams
Lungimea poate varia de la 18 la 24 m. / Lenght can vary between 18 and 24 m.
Vedere 3D / 3D view
Grinzi de pod 93 şi 103 cm / Bridge beams 93 and 103 cm
Grinzile de pod sunt asimilate din gama de produse IPTANA pentru diferite deschideri şi sarcini, cu secţiune I şi T, cu deschideri între 18 şi 24 metri. Pro-dusele fiind de catalog, suportă modificări şi adaptări în limita acceptării aces-tora de către proiectanţi.
Bridge beams are assimilated from the IPTANA products range for various spans and loads, with I and T sections, with spans between 18 and 24 meters. As catalogue products can be modified and adapted in the acceptance limit of the designers.
89
1184
4
55
55
5
445
40 4010R=10
10
102
1024
512
118
103
50 75 5 5 5
4 4
5 5 5 5 75
R=20 R=20
R=10
18
Produse - Grinzi de pod / Products - Bridge beams
Dispunere toroane / Strands layoutSecţiune caracteristică / Specific sectionSecţiune transversală / Cross section
L (m)Încărcare admisă
Valoare caracteristică(kN/ml)
18 42.5
21 27.5
24 21.5
L (m)Încărcare admisă
Valoare caracteristică(kN/ml)
18 46.5
21 33.5
24 24.5
42 421010
120
16
R = 10
R = 20 78
6
1 145
47
82
015 93
5 1221
120
539
4 4
5 5 5 5 5 5 5 5
45
55
55
4
Dimensiuni / Dimensions
Grindă de pod 93 / 93 Bridge beam Grindă de pod 103 / 103 Bridge beam
90
Lungimea poate varia de la 30 la 41 m. / Lenght can vary between 30 and 41 m.
Vedere 3D / 3D view
Vedere de sus / Top view
Vedere laterală / Side view
Grinzi de pod 150 cm / Bridge beams 150 cm
Grinda de pod cu secţiune I este un proiect propriu, conceput de către proiec-tanţii noştri de specialitate, pentru înălţime de 1.50 m şi deschideri cuprinse între 30 şi 41 m.
The I section bridge beam is an original project designed by our expert design-ers, for a height of 1.50 m and openings varying between 30 and 41 m.
Produse - Grinzi de pod / Products - Bridge beams
91
Dispunere toroane / Strands layoutSecţiune caracteristică / Specific sectionSecţiune transversală / Cross section
L (m) Greutate (tone)/buc
30 37.45
41 51.18
Dimensiuni / Dimensions
Produse - Grinzi de pod / Products - Bridge beams
92
Vedere 3D / 3D view
Canivouri din beton armat / Reinforced concrete channel elements
Acest tip de elemente prefabricate din beton se foloseşte pentru protejarea conductelor de apă, liniilor electrice şi fibrei optice din subteran. Se pot realiza carosabile sau necarosabile, drepte sau curbe, simple sau duble, în funcţie de solicitarea clientului.
This type of precast concrete elements is used for protection of underground water pipes, electric cables and fiber optic lines. The elements can be executed for carriage way or non-carriage way, straight or curved, single or double, de-pending on customer’s request.
Produse - Canivouri / Products - Channel elements
93
d
a b a
c
e
a
a
aba
c
Secţiune caracteristică / Specific sectionSecţiune transversală / Cross section
ab ba a
e
a
c
ad
ab ba a
c
Produse - Canivouri / Products - Channel elements
Notă: dimensiunea variază în funcţie de specificul proiectului. / Note: size varies depending on the type of the project.
9494
ASA CONS ROMÂNIA SRLStr. 22 Decembrie 1989 nr. 27401113 Turda · RomâniaTel. +40 264 312 765 · Fax +40 264 317 057 contact@asacons.ro · www.asacons.ro · www.consolis.ro
top related