catalog accesorii incendiu

8/10/2019 Catalog Accesorii Incendiu

1/105

GE Security

FIRE SYSTEM ACCESSORIES

Product catalogue


2/105

ASPIRATION SYSTEMS


3/105

Page 2

Aspiration Systems

Technical Data

Protection IP54

Housing ABS

Operating temperature -20C to +50C

Dimensions 300 x 150 x 110 mm

Ordering Information

DD700 Single pipe universal duct detector

One-tube air sampling system

Conventional or analogue detectors

Test hole on cover

Simple installation

Sensitive flow indication

Filter for dusty environments

Simple service and maintenance

Installer-friendly connection of cables

Foolproof installation of sampling tube

Optional booster fan

Special profile for 700 series and 2000 series detectors

Special profile for 300 series and 1500 series detectors

Single pipe universal duct detector DD700


4/105

General

The ASD20 Aspiration Smoke Detector consists of an analysis chamber with

one or two smoke detectors, which can be of conventional or analogue

technology, ionisation or optical. The smoke reaches the analysis chamber

through the installation pipes after having been sucked in by a turbine inside

the ASD20 system. An electronic circuit controls said turbine and the air flow,

giving off a fault signal if the pipes are broken or if the air intake is

obstructed. It has two voltagefree relays for local manoeuvres, one per

detector, and a third system fault relay. When analogical smoke detectors

from the 700A series are used, it is possible to adjust their sensitivity levels

from the fire control unit.

Technical Data

Power supply voltage 24 V

Consumption on standby 250 mA

Consumption 1st alarm 280 mA

Consumption 2nd alarm 320 mA

Fault consumption 220 mA

Working temperature -10 to +60C

Storage temperature -10 to +70C

Relative humidity


5/105

Page 4

Aspiration Systems

The FASD710 provides a low cost solution for aspiration systems using pointsmoke detectors. The controller can be used in many applications where point

smoke detectors are not suitable. The powerful pump allows pipe distances of

up to 50 metres

Technical Data

Supply voltage 24V DC

Current consumption 225mA

Number of detectors (not included) 2

Filtration Cartridge dust particle filter

Maximum tube length 50m

IP rating IP65


FASD710 High-performance aspiration controller for point detectors

FHSD771 Large bore red pipe 3 metre length

FHSD772 Straight union large bore

FHSD774 45 deg. elbow for large bore pipes

FHSD775 End cap for large bore pipes

FASD710

2 detectors for redundancy and mixed detection strategy.

Up to 50 metres pipe

Cartridge air filter

Bar graph indication of flow

high / low flow fault and remote reporting

IP65 rating

Hotels

Banks

Hospitals

Livestock Buildings

Prisons

Underground stations

Aesthetic environments

Harsh environments

Dirty environments

High-performance aspiration controller for point detectors FASD710


6/105

Page 5

Aspiration Systems

Compact and powerful, the FHSD720 has all the detection and monitoringfeatures of big aspiration systems. It is ideal for monitoring localised areas

up to 850m. All data can be uploaded or downloaded via the standard RS232

or RS485 ports

Technical Data

Power supply 24V, 600ma min, 1,5A max

Smoke detector Resolution 0.005%, range 20%

Light source 50mW 660nm high power laser diode

Number of inlets 2 (ground and ceiling), 1 address

Pipe size 25mm Oudside Diameter

Pipe lenght 70 meters

Aspirator 800Pa static pressure

Area coverage 850m

Alarm levels 4: alert, action, fire1, fire2Alarm setting range 0.005% - 20.0%

Outputs 4 alarm relays, 1 fault relay, 1A change over

Communication RS232, Modbus, RS485

Weight 3kg

Humidity 0-95%

Temperature 0 - 50 C


FHSD720 Localised aspirated early warning smoke detection system

FHSD720RL Relay Module 4 Channel for FHSD72x

FHSD732 Single channel remote disp lay & programmer

FHSD733 Remote display repeate r un it - 16 un its

FHSD751 Filter+ with fi lter element - harsh environmentFHSD754 Rep lacement f il te r e lement for the FHSD751



FHSD773 90 deg. bend for large bore pipes



IP65

RS232 and RS485 standard

High Power Pump

High sensitivity laser detector

Four alarm levels

Remote display units

24V operation

Fault monitoring

Small EDP rooms

Server rooms

Escalators

Machine protection

Localised aspirated early warning smoke detection system FHSD720


7/105

Page 6

Aspiration Systems

The FHSD721 and FHSD721D four pipe aspirating laser detector systemprovides very early warning to smoke over a very large area. Each pipe can be

up to 100 metres long. The FHSD721D is complete with display, programmer

and web server.

Technical Data

Power supply 24V, 600ma min, 1.5A max

230V 5A PSU and battery charger, optional

Smoke dectector Resolution 0.005%, range 20%


Expected lifetime 10 years

Number of inlets 4 (non addressable)

Pipe size 25mm outside diameter

Pipe length 100 meters each

Aspirator 2000Pa high vacuum centrifugal blowerAlarm levels 4: alert, action, fire1, fire2

Alarm setting range 0.005% - 20.0%

Alarm delay 0 - 60 secs, individually programmable

Outputs 4 alarm relays, 1 fault relay, 1A c/o

Communication RS232, Modbus RS485

Webserver option (FHSD721D only) Ethernet 10 BaseT/RS232 MODEM, TCP / IP

Weight 24V: 10.7 kg, 230V PSU: 14.5 kg

Humidity 0 - 95 %



FHSD721 Four pipe, one address aspirated early warning smoke detection system

FHSD721D 4 pipe 1addr. aspir. early warning smoke detection system c/w displayFHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215


FHSD731 Conversion kit for remote display



FHSD751 Filter+ with fi lter element - harsh environment

FHSD754 Rep lacement f il te r e lement for the FHSD751






Early warning applications

Detection with high airflows

Unobtrusive detection

Ideal for large open areas

For inaccessible areas

For dusty and humid environments

For tamperproof installations

Webserver optional

Four pipe, one address aspirated early warning smoke detection system FHSD721


8/105

Page 7

Aspiration Systems

The FHSD724 four channel large bore aspirating laser detector systemprovides very early warning to smoke over a very large area. Each pipe can be

up to 100 metres long. The unit is complete with display and programmer.

Technical Data


230V 5A PSU / battery charger, optional




Number of inlets 6, fully addressable


Pipe length 100 meter each

Aspirator 2000 Pa high vacuum centrifugal blower

Alarm levels 4: alert, action, fire1, fire2Alarm setting range 0.005% - 20%

Alarm delay 0 - 60 secs, individually programmable



Web server Communication: Ethernet 10 BaseT/RS232 MODEM,

TCP / IP

Weight 24V: 10.7 kg, 230V PSU: 14.5kg

Humidity 0 - 95%



FHSD724D Four channel four area aspirated early warning smoke detection system

FHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215













Detection with high inflows






Four channel four area aspirated early warning smoke detection system FHSD724D


9/105

Page 8

Aspiration Systems

High sensitivity detection

The FHSD726 six channel large bore aspirating laser detector system provides

very early warning to smoke over a very large area. Each pipe can be up to 100

metres long. An environmental detector is also available

Technical Data


Smoke Detector Resolution: 0.005%, range: 20%

Light Source 50mW 660nm high power laser diode

Expected life time 10 years

Number of inlets 6 (fully addressable)


Aspirator 2000Pa high vacuum centrifugal blower


Alarm levels 4


Alarm delay 1-60 Secs, individually programmable

Outputs 4 alarm relays, 1 A C/O


Web Server Ethernet 10 BaseT/RS232 MODEM, TCP / IP

Environmental

Weight 24V 10.7 KG, 230VPSU 14.5 KG

Humidity 0-95%


FHSD726D Aspirating laser detector six pipe complete with display

FHSD726DE Aspirating laser and environmental detector, six pipe c/w displayFHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215



















Six channel six area aspirated early warning smoke detection system FHSD726


10/105

Page 9

Aspiration Systems

Selective detection

The FHSD7215D 15 channel micro bore aspirating laser detector system

provides very early warning to smoke over a very large area. Fifteen fully

addressable areas. Each pipe can be up to 50 metres long.

Technical Data





Number of inlets 15, fully addressable

Tube size Micro bore 6mm o.d, 4mm i.d , flexible nylon or FEP

tubing

Aspirator 0.8 bar rotary vane vacuum pump


Alarm levels 4: alert, action, fire1, fire2


Alarm delay 0-60 seconds, individually programmable



Web server Ethernet 10 BaseT/RS232 MODEM, TCP / IP

Weight 24V: 10.7 kg, 230V PSU: 14.5 kg

Humidity 0 - 95 %


FHSD7215D 15 Channel Micro bore aspirated early warning smoke detection system

FHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215FHSD720RL Relay Module 4 Channel for FHSD72x




FHSD752 Filter in-line single stage

FHSD753 Filter in-line 3 stage

FHSD755 Replacement filter element set - medium / fine for the FHSD753

FHSD756 Replacement filter element pack of 10 - coarse - for the FHSD753

FHSD761 Micro bore 6mm sampling tube - 30 meter ree l

FHSD762 Straight union fo r micro bore 6mm tube

FHSD763 Tee union for micro bore 6mm tube

FHSD764 Scintered end of l ine f il ter for micro bore 6mm tube








Micro bore pipes

15 Channel Micro bore aspirated early warning smoke detection system FHSD7215D


11/105

Page 10

Aspiration Systems

A 230V power supply, battery charger and battery container for the FHSD721,FHSD724, FHSD726, and FHSD7215 apiration systems. The power supply is

easily mounted in the units.


FHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215

PSU Batt charger 230V for FHSD721-FHSD7215 FHSD720PS

This four way relay module extends the outputs of the FHSD72x aspiration

systems. It is plug-in installable.



Relay Module 4 Channel for FHSD72x FHSD720RL


12/105

Page 11

Aspiration Systems

This kit allows the display panel of a FHSD72xD aspiration system to beremoved from the unit and to be mounted remotely.



Conversion kit for remote display FHSD731



Single channel remote display & programmer FHSD732


13/105

Page 12

Aspiration Systems

A remote display channel allowing the connection of up to16 aspirationsystems on a RS485 bus.



Remote display repeater unit - 16 units FHSD733

For use with large bore systems



Filter+ with filter element - harsh environment FHSD751


14/105

Page 13

Aspiration Systems

A single stage filter for micro-bore systems


FHSD752 Filter in-line single stage

Filter in-line single stage FHSD752

A three stage filter with course, medium, and fine filters for micro-bore

systems


FHSD753 Filter in-line 3 stage

Filter in-line 3 stage FHSD753


15/105

Page 14

Aspiration Systems



Replacement filter element for the FHSD751 FHSD754


FHSD755 Replacement filter element set - medium / fine for the FHSD753

Replacement filter element set - medium / fine for the FHSD753 FHSD755


16/105

Page 15

Aspiration Systems


FHSD756 Replacement filter element pack of 10 - coarse - for the FHSD753

Replacement filter element pack of 10 - coarse - for the FHSD753 FHSD756


FHSD761 Micro bore 6mm sampling tube - 30 meter ree l

Micro bore 6mm sampling tube - 30 meter reel FHSD761


17/105


18/105

Page 17

Aspiration Systems


FHSD764 Scintered end of l ine f il ter for micro bore 6mm tube

Scintered end of line filter for micro bore 6mm tube FHSD764



Large bore red pipe 3 metre length FHSD771


19/105

Page 18

Aspiration Systems



Straight union large bore FHSD772



90 deg. bend for large bore pipes FHSD773


20/105

Page 19

Aspiration Systems



45 deg. elbow for large bore pipes FHSD774



End cap for large bore pipes FHSD775


21/105

FLAME DETECTORS


22/105

Page 21

Flame Detectors

Technical Data

Supply Voltage 12 - 30 V dc

Supply current 3 mA quiescent

Relay contact ratings 1A @ 30 V dc (resistive load)

Field of view Up to 120

Spectral response (UV) 185 to 260 nm

Operating temperature -10C - 60C

Relative Humidity 95% Non condensing

Weight 150 g (including base)


FF711 UV f lame detec tor complete w ith s tandard 2 wi re base

FF711R 24 V dc relay base for FF 711

UV, IR and UV/IR models

Low cost units for indoor applications

Flame proof model available

Fast response (1 - 2 seconds)

Wide operating voltage

Wide cone of vision - up to 120

2 Wire and relay operation

Versatile, adjustable test torch available

Universal mounting bracket

UV flame detector complete with standard 2 wire base FF711


23/105

Page 22

Flame Detectors

Technical Data


Supply current 4 mA






Weight 655 g


FF713 UV f lame detec tor sel f contained wi th fi re and faul t relays










UV flame detector self contained with fire and fault relays FF713


24/105

Page 23

Flame Detectors

Technical Data


Supply current 3 mA quiescent






Weight 2.2 kg


FF716 UV f lame detec tor with f ire relay in flame proo f enclosure










UV flame detector with fire relay in flame proof enclosure FF716


25/105

Page 24

Flame Detectors

Technical Data


Supply current 67A


Field of view 100

Spectral response (IR) Near 4.3um



Weight -


FF721 IR flame detector complete with 2 wire base










IR flame detector complete with 2 wire base FF721


26/105

Page 25

Flame Detectors

Technical Data

Supply voltage 14 - 28 V dc

Supply current 3/9, 4/8/14, 4-20, 8-20 mA

Relay contact ratings 1 A @ 30 V dc (resistive load)

Field of view 90 min. cone

Spectral response (IR) 1.0 to 2 m

Operating temperature -10C to 55C

Storage temperature -20C to 65C

Relative humidity 95%; non-condensing

IP Rating IP64 poly carbonate box

IP65 die-cast zinc alloy boxIP66 flame proof box

Weight 1 kg die-cast zinc ally box

2 kg flame proof box


FF741 Dual IR f lame detector in glass reinforced polycarbonate housing

FF742 Dual IR flame detecto r in d ie-cast zinc al loy housing

FF746 Dual IR flame detecto r in Eexd - I IC T6 flame proof housing

FF747 Dual IR Intrinsic safe flame detector in die-cast z inc alloy housing

Dual IR and UV/Dual IR models

High specification units for critical applications

IP65 Housing available

Flame proof and Intrinsic safe models

Low current consumption

2 Wire, 4 - 20 mA and relay operation

Latching and non latching operation

High / Low sensitivity setting

Versatile mounting brackets

Tolerance to detector window contamination


Remote self test facility

Microprocessor controlled

Immunity to false sources (arc welding, lightning and static)

Conforms to EN54: Part 10

Dual IR flame detector in glass reinforced polycarbonate housing FF741


27/105

Page 26

Flame Detectors

Technical Data


Supply current 3/9, 4/8/14, 4-20, 8-20 mA

Relay contact ratings 1 A @ 30 V dc (resistive load)

Field of view 90 min. cone

Spectral response (IR) 1.0 to 2 m

Operating temperature -10C to 55C

Storage temperature -20C to 65C

Relative humidity 95%; non-condensing

IP Rating IP64 poly carbonate box

IP65 die-cast zinc alloy boxIP66 flame proof box

Weight 1 kg die-cast zinc ally box

2 kg flame proof box


FF751 UV / Dua l IR f lame detec tor in die cast zinc al lo y housing

FF756 UV / Dual IR f lame detector in Eexd - I IC T6 f lame proof housing Dual IR and UV/Dual IR models

High specification units for critical applications

IP65 Housing available

Flame proof and Intrinsic safe models


2 Wire, 4 - 20 mA and relay operation

Latching and non latching operation

High / Low sensitivity setting

Versatile mounting brackets

Tolerance to detector window contamination


Remote self test facility


Immunity to false sources (arc welding, lightning and static)

Conforms to EN54: Part 10

UV / Dual IR flame detector in die cast zinc alloy housing FF751


28/105

Page 27

Flame Detectors

A microproccessor universal test torch that can test all FF700 series flamedetectors. It emits various channels of infra-red to test dual IR detectors. It

also can emit 'flickering' IR to test for false alarms.


FF703 UV/IR universal test torch

UV/IR universal test torch FF703

A universal swivel mounting bracket for most FF700 flame detectors.


FF705 Adjustable mounting bracket

Adjustable mounting bracket FF705


29/105

Page 28

Flame Detectors

A weather shield that can be used for most FF700 flame detectors


FF706 Stainless steel weather shield

Stainless steel weather shield FF706


30/105

BEAM DETECTORS


31/105

Page 30

Beam Detectors

Technical Data

Supply Voltage 11.5 - 28 VDC

Current consumption

Quiscent less than 13 mA

Alarm less than 20 mA

Operating Temperature -20 to 55 C

Size

Control Unit 210 x 160 x 80 mm

Heads 83 x 115 x 135 mm

IP Rating

Control Unit IP 50Heads IP 50

Construction

Control Unit Double pressed steel sheet

Heads Zinc alloy

Colour

Control Unit White RAL 9010

Heads White RAL 9010

Certification VdS


FD2000 Beam smoke detector

FD2010 Beam smoke detector flame proof

Large area coverage up to 1500 m per unit

Range from 10 to 100m

Up to ceiling heights of 25 m

12 to 24 VDC


Manual or automatic reset

3 selectable alarm thresholds

Self check and automatic signal compensation

Automatic discrimination between fire and fault

Retro operation through prisms

Ground level electronics

Easy wiring and alignment

Conforms to BS5839 part 5

VdS approved

Atex explosion-proof version

Beam smoke detector FD2000


32/105

Page 31

Beam detectors

Technical Data

Supply voltage 10.2 - 30 V dc

Range

FD 705R 5 - 50 m

FD 710R 50 - 100 m

Lateral detection 7.5 m

Current consumption

Quiescent < 4 mA

Alarm < 15 mA

Optical wave length 880 nm

Operating temperature -30C to 55CSize 210 x 130 x 120 mm

IP rating IP50

Construction Flame retardent ABS

Colour Gray-black


FD705R Reflective beam smoke detector 5 - 50m

FD710R Ref lec tive beam smoke detecto r; 50 - 100 m

Area coverage up to 600 m 2 per unit

Range from 5 - 50 m and 50 - 100 m

Up to ceiling heights of 25 m

10 to 30 V dc operation


Manual or automatic reset

3 selectable alarm thresholds

Self check and automatic contamination compensation

Automatic discrimination between fire and fault

Retro operation through prism

Vertical or horizontal mount

Easy wiring and unique alignment


Conforms to BS 5839 part 5, EN54,VdS and UL

Reflective beam smoke detector 5 - 50m FD705R


33/105

LINEAR HEAT DETECTION


34/105

Page 33

Linear Heat Detection

Technical Data

Operating voltage range Volt dc 18-30

Operating current (typical) mA

Quiescent 28

Alarm 58

Operating temperature C -25 to +50

Relay contact rating (fire and fault) 1 A @ 30 V dc

IP rating IP65

Dimension (H x Wx D in mm) 80 x 80 x 52

Colour Grey, RAL 9002


DT650L Conventional control ler for analogue linear heat cable

Conventional and analogue addressable controllers

Monitoring at the point of risk

Choice of temperatures

Ease of installation

Reliable and durable

Intrinsic safe solutions

Ideal for smoke less fires - overheating cables

VdS approved

Conventional controller for analogue linear heat cable DT650L

Technical Data

Operating voltage range Volt dc 18-30Operating current (typical) mA

Quiescent 2

Alarm 3.2

Operating temperature C -25 to +50

Relay contact rating (fire and fault) -

IP rating IP65

Dimension (H x Wx D in mm) 105 x 105 x 65

Colour Grey, RAL 9002


DT950L 950 series addressable control ler for analogue linear heat cable

Conventional and analogue addressable controllers Monitoring at the point of risk






VdS approved

950 series addressable controller for analogue linear heat cable DT950L


35/105

Page 34


Technical Data

1m alarm temp C 70-125


Operating temp C -20 to +70

Outer sheath material Red PVC

Dimensions (diameter in mm) 2.8


HC650 Analogue linear heat cable PVC 500 meter


Analogue linear heat cable






VdS approved with DT650L & DT950L controllers

Analogue linear heat cable PVC 500 meter HC650


36/105

Page 35


The Rilsan coating gives a high resistance to chemical substances

Technical Data




Outer sheath material Rilsan coated

Dimensions (diameter in mm) 4


HC650R Analogue l inear heat cable with Rilsan coating 500 meter

DT650L Conventional control ler for analogue linear heat cableDT950L 950 series addressable control ler for analogue linear heat cable








Analogue linear heat cable with Rilsan coating 500 meter HC650R


37/105

Page 36


The stainless steel coating gives high mechanical strength.

Technical Data




Outer sheath material Stainless steel



HC650S Analogue linear heat cable with stainless steel covering - 500 meter










Analogue linear heat cable with stainless steel covering - 500 meter HC650S

The Rilsan and stainless steel covering gives mechanical strength and

chemical resistance

Technical Data




Outer sheath material Rilsan and Stainless steel



HC650RS Analogue linear heat cable - Rilsan and stainless steel cover - 500 m



Analogue linear heat cable Conventional and analogue addressable controllers






Analogue linear heat cable - Rilsan and stainless steel cover - 500 meter HC650RS


38/105

Page 37


A range of digital heat senging cable from 68C to 235C

Technical Data

Max operating voltage 100 V ac/dc

Conductor resistance 100 Ohm/km

Alarm temp C 68

Max ambient C 45

Outer sheath material Polythene Braid

Colour/Marking Red/Green tracer



HCD607 Dig ita l heat sens ing cab le 68C - 500 meter

HCD609 Dig ita l heat sens ing cab le 88C 500 meter




Digital linear heat cable







Digital heat sensing cable 68C - 500 meter HCD607


39/105

Page 38



HCA601 A clip for heat cable 100/pack

'A' clip for heat cable 100/pack HCA601


HCA602 P clip for heat cable 100/pack

'P' clip for heat cable 100/pack HCA602


40/105

Page 39



HCA603 T clip for heat cable 100/pack

T' clip for heat cable 100/pack HCA603

HCA 605-x

A range of edge clips to fit on structures from 2 to 20 mm


HCA605-3 Edge clip for heat cable 2-3 mm 100/pack

HCA605-8 Edge clip for heat cable 3-8 mm 100/pack

HCA605-14 Edge cl ip for heat cable 8-14mm 100/pack

HCA605-20 Edge clip for heat cable 14-20mm 100/pack

Edge clip for heat cable 2-3 mm 100/pack HCA605-3


41/105

CO DETECTION


42/105

Page 41

CO Detection

The KM-Series CO detection system is designed for applications such as

vehicle parking areas where concentrations of CO may accumulate. The range

is compliant with the UNE23.300/84 standard. The KM260/1 is a 1 to 5 zonescontrol unit, using KM170 detectors.

Technical Data

Power Supply

Mains Supply 230 VAC 10% 50 Hz

Power Consumption 95 W (max)

Zone Configuration

Zone Input Voltage 10-20 VDC/VAC

Sensitiviy 0-300 ppm

Cable Requirement 3 core 1.5 mm

Cable Length (max) 350 m

No. of Detectors (max) 15

No. of Zones (max) 5

MechanicalHousing (w x h x d) 275 x 335 x 130 mm

Weight 6 kg


KM260/1-ING CO detection control panel - 1 Zone

KM260/2-ING CO detection control panel - 2 Zones




Designed according to norm 23300/84

Miner CDM8001 and CDM8002 standard password

LGAI 154.909 and 96013132 standard certification

Easy to use


Direct reading of measured levels

Easy installation

Extraction relays and alarm outputs per area

From 1 to 5 areas

3-wire system

Modular design

Up to 15 detectors per zone

10 seconds response time

Elegant design

Supervision of all zone lines

Available in various languages

CO detection control panel - 1 Zone KM260/1-ING

CO detection control panel - 2 Zones KM260/2-ING





43/105

Page 42

Expansion Module

The KM260 is an expansion module for the KM260-Series CO panels from GE-Interlogix. It allows for an additional monitoring zone to be added to the

control panel, each module allowing for an additional 15 sensors to be

connected.

Technical Data

Power Supply

Mains Supply 230 VAC 10% 50 Hz

Power Consumption 95 W (max)

Zone Configuration

Zone Input Voltage 10-20 VDC/VAC

Sensitiviy 0-300 ppm

Cable Requirement 3 core 1.5 mm

Cable Length (max) 350 m

No. of Detectors (max) 15No. of Zones (max) 1


KM260-ING CO detection expansion module (English Version)

Designed according to norm 23300/84

Miner CDM8001 and CDM8002 standard password

LGAI 154.909 and 96013132 standard certification

Easy to use


Direct reading of measured levels

Easy installation

Extraction relays and alarm outputs per area

3-wire system

Up to 15 detectors per zone

10 seconds response time

Supervision of zone line

Available in various languages

CO detection expansion module (English Version) KM260-ING


44/105

Page 43

Detectors

The KM170 detector is specifically designed to react to the presence of carbonmonoxide. The design complies with the requirements of the UNE 23-300

standard.

Technical Data

Sensor Type TGS Semicondictor

Useful Life 4 years

Electrical Characteristics

Supply Voltage 10 to 20 VDC

Quiescent Current 35 mA

Reaction Time 10 s

Environmental

Operating Temperature 0 to 40 C

Protection Index IP205

MechanicalSize (h x ) 81 x 109 mm

Weight 115 g

Material and Colour ABS White

Installation

Number of detectors per zone 15

Covarage 300 m


KM170 CO detector wi th base and mount ing supplement

Complies with the requirements of the UNE23-300 standard

Microprocessor based

Resolution of up to 5 ppm

Response time of 10 s


Local status indication of:

- Normal operation

- 50 ppm detected

- Fault

Useful life of up to 4 years

CO detector with base and mounting supplement KM170


45/105

MANUAL CALL POINTS


46/105

Page 45

Manual Call Points

DM700 Series

A range of call points with flying leads that can but flush mounted or surface

mounted using a back-box

Technical Data

Material Self-extinguishing Noryl SE100

Max. contact rate resistive load

50 V ac or 30 V dc 8 A

50 V dc 3 A

Contact resistance Max. 50 milliohm

Series resistor -

Colour Red - RAL N3020

Operating temperature -40 to +85C

Relative humidity max. 90% RV


DM700 Manual callpoint, flying leads

DM700B Manual callpoint, flying leads, blue

DM700R Manual callpoint, f ly ing leads, 470 Ohm series resistor

DM700RB Manual callpoint, flying leads, 470 Ohm series resistor, blue

DM700L Manual callpoint, flying leads, 470 Ohm series resistor & LED

DM700LB Manual callpoint, flying leads, 470 Ohm series resistor & LED, blue

DM700G Manual ca llpoin t, fl ying leads , green

DM711 Glass, EN54, Aritech

DM715 Glass, EN54, Universal

Easy to install

With or without series resistor

With or without LED

With breakglass or resettable

Easy to replace glass

Surface and flush mounting options

High quality micro switch

Glass protected with foil

Standard EN54 symbol

Standard accepts hinged cover

Key test facility

Manual callpoint, flying leads DM700


47/105

Page 46

Manual Call Points

Technical Data

Material - standard Self-extinguishing Noryl SE 100


50 V ac or 30 V dc 8.0 A

50 V dc 3.0 A

Contact resistance Max. 50 milliohms

Standard colour Red - RAL N 3020

Ambient temperature range -40 to + 85 C

Maximum relative humidity 90% RV


DM700E Surface mount manual callpoint IP67, including blackbox

DM700E

Easy to install




IP67

EN54 approved

Surface mount manual callpoint IP67, including blackbox DM700E


48/105

Page 47

Manual Call Points

Technical Data

Material - standard Glass reinforced polycarbonate

Contact resistance Max. 50 milliohms

Standard colour Red - RAL N 3020

Ambient temperature range -55 to + 55 C

Maximum relative humidity 90% RV


DM700IS Surface mount IP 66/67 intrinsic safe MCP, including back box

Easy to install





Glass protected with foil

ATEX approved

Preformed mounting slots

Key test facility

Surface mount IP 66/67 intrinsic safe MCP, including back box DM700IS


49/105

Page 48

Manual Call Points

DM700 Series

Technical Data

Material Self-extinguishing Noryl SE100


50 V ac or 30 V dc 8 A

50 V dc 3 A

Contact resistance Max. 50 milliohm

Series resistor -

Colour Red - RAL N3020

Operating temperature -40 to +85C

Relative humidity Max. 90% RV


DM700K Manual ca llpoin t wi th keyswitch, fl ying leads

DM700KB Manual callpoint with keyswitch, flying leads, blue Easy to install


High quality key switch

Operates after long period of disuse

Standard EN54 symbol

Preformed mounting slots

Manual callpoint with keyswitch, flying leads DM700K


50/105

Page 49

Manual Call Points

A standard EN54 glass for DM700 series of call points, with Aritech logo


DM711 Glass, EN54, Aritech

Glass, EN54, Aritech DM711

A universal EN54 approved glass for the DM700 series of detectors, no logo


DM715 Glass, EN54, Universal

Glass, EN54, Universal DM715

A hinged transparent cover to protect accidental operation of DM700 series

manual call points


DM782 Hinged transparent MCP protection cover

Unobtrusive

Transparent

Protects from accidental alarm activation

Hinged transparent MCP protection cover DM782


51/105

Page 50

Manual Call Points

A back box for the surface mounting of DM700 call points, without connectors


DM788 Surface mount box without connectors

DM788Y Sur face mount box wi thout connectors, ye ll ow

DM788B Sur face mount box wi thout connectors, blue

Surface mount box without connectors DM788

A surface mount box with three connectors for DM700 series manual callpoints.


DM787 Surface mounting box with connectors

DM787Y Sur face mounting box wi th connectors, ye ll ow

DM787B Sur face mounting box wi th connectors, blue

DM787G Sur face mounting box wi th connectors, green

Surface mount back box for MCP - RED

Surface mounting box with connectors DM787


52/105

Page 51

Manual Call Points

General

The PK20 manual call point is a manual alarm activation point for

conventional detection systems. Once activated, it remains activated until it

is manually reset using a key. To reset, simply turn the key a turn to the

right and it is ready for use.

This call point has been designed for indoor use.

Technical Data

Size 100 x 95 x 43 mm

Max. recommended distance between units 60 m

Installation height 1.2 - 1.5mFastening screws 2x (3.5 x 30 mm)

Power supply voltage 24 VDC

Consumption in standby 0 mA

Consumption in alarm 60 mA

Status Indications Standby, Alarm

Working temperature -10 to 50C

Storage temp. -10 to 50C

Max. relative humidity 95%


PK20 Resetable Manual Call Point

PK20M Flush mount cradle

PK20T Hinged transparent MCP protection cover

Standard labelling (pictograms)

Spare crystals not required

Easy installation

Easy maintenance

Accessory for flush mount (optional)

Transparent protection cover (optional)

For conventional systems

Modern, robust and elegant design

Resetable Manual Call Point PK20

Accessory for PK20 restable manual callpoint. This cradle allows for the PK20

to be flush mounted.


PK20M Flush mount cradle

Allows flush mounting of the PK20 manual call point

Flush mount cradle PK20M


53/105

Page 52

Manual Call Points

Accesory for PM20 resetable manual callpoint. Made of transparent plasic, itprevents the manual call point from being accidentally activated.


PK20T Hinged transparent MCP protection cover

Unobtrusive

Transparent

Protects from accidental alarm activation

Hinged transparent MCP protection cover PK20T


54/105

FIRE INDICATORS


55/105

Page 54

Fire indicators

This low current remote indicator can be used with all 650, 950, 700 & 2000series detectors, and can also be used in intrinsic safe applications.


AI671 Mini disc remote indicator

Mini disc remote indicator AI671


56/105

Page 55

Fire indicators

Technical Data

Material Self-extinguishing polycarbonate

Dimensions (L x W x H) 80 x 80 x30 mm

Colour White RAL 9010

Operating voltage 12-28 V dc

Current consumption 4 mA nominal

Flashing frequency 1.3 Hz

Light intensity 200 mcd

Colour LEDs RED


AI672 Optical Remote Indicator



Universal mounting plate

Low profile

Clearly visible, large LEDs

Protected against polarity reversal

Connects up to 4 detectors

Blinking or fixed LEDs

High sound output

With and without sounder

Optical Remote Indicator AI672

Technical Data

Material Self-extinguishing polycarbonate

Dimensions (L x W x H) 80 x 80 x 30 mm

Weight 55 g

Colour White RAL N 9010

Surface Textured

Terminals 5

Operating Voltage 12 - 28 V dc

Current consumption 4 mA nominal

Flashing frequency 1.3 Hz

Light intensity 200 mcd

Colour LEDs Red

Sound pressure 81 dBA 1 metreFrequency 3600 Hz


AI673 Optical and Accustical Remote Indicator



Universal mounting plate

Low profile

Clearly visible, large LEDs

Protected against polarity reversal

Connects up to 4 detectors

Blinking or fixed LEDs

High sound output

With and without sounder

Optical and Accustical Remote Indicator AI673


57/105

Page 56

Fire indicators

Technical Data

Electrical Specifications


Activation Voltage 18 to 27 VDC

Current Consumption 600 mA

Switching Polarity NA

Indicators 24 V 3 W

Environmental Specifications

Working Temperature -10 to 75 C

Physical Specifications

Number of zones NA

Buzzer output 80 dB

Housing Colour Grey

Display Colour RedWeight 700 g


KR24 Illuminated extinguishing waring sign (Spanish version) 24VDC

KR Repeaters

- Zone indication with alarm buzzer

- Local buzzer silence control

- Local buzzer silenced indication

- Alarm indicated until removed

KR Signs

- Low current consumption

- Large angle of view

- Optical and acoustic indications selectable

- Modern and elegant design

Illuminated extinguishing waring sign (Spanish version) 24VDC KR24


58/105

Page 57

Fire indicators

The KR24 is specifically designed as an evacuation warning sign for gas

extinguising areas. The KR24B has no text on the backlit display, and text may

therefor be added as required for the application. Units supplied with text in

various languages are also availble.

Technical Data






Indicators 24 V 3 W




Number of zones NA

Buzzer output 80 dB

Housing Colour Grey

Display Colour Red

Weight 700 g


KR24B Illuminated warning sign (No text) 24VDC





Illuminated warning sign (No text) 24VDC KR24B

The KR24 is specifically designed as an evacuation warning sign for gasextinguising areas. The KR24B has no text on the backlit display, and text may

therefor be added as required for the application. Units supplied with text in

various languages are also availble.

Technical Data






Indicators 24 V 3 W




Number of zones NA

Buzzer output 80 dB

Housing Colour Grey

Display Colour Red

Weight 700 g


KR24B Illuminated warning sign (No text) 24VDC





Illuminated warning sign (No text) 24VDC KR24B


59/105

Page 58

Fire indicators

The PA25 series remote indicators have been designed for direct connection tofire detectors, enabling luminous indication outside the area where the

detector is installed.

Technical Data


Supply Voltage (Analogue Systems)5 to 10 VDC

Supply Voltage (Conventional Systems) 2 to 5 VDC

Current Consumption < 50 mA

Mechanical Specifications

Size (w x h x d) 80 x 80 x 42 mm

Weight 10 g

Box material A.B.S.

Colour White

Environmental SpecificationsProtection level IP20

Working temperature -10 to +60 C

Storage temperature -10 to +70 C


PA25/3L Low current remote LED indicator Direct two-wire connection to detector

Large angle of visibility - lit up on four sides


Flashing option

2 to 28 VDC power supply (depending on model)

High luminosity

Compatible with third party products

IP20 protection level

Modern and elegant design

ABS plastic casing with ruby red polycarbonate spy-hole

Shock resistant

Low current remote LED indicator PA25/3L


60/105

Page 59

Fire indicators



Technical Data



Supply Voltage (Conventional Systems) NA




Weight 10 g

Box material A.B.S.

Colour White





PA25/9 Remote LED indicator 9 VDC Direct two-wire connection to detector



Flashing option


High luminosity





Shock resistant

Remote LED indicator 9 VDC PA25/9


61/105

Page 60

Fire indicators



Technical Data



Supply Voltage (Conventional Systems) NA




Weight 10 g

Box material A.B.S.

Colour White





PA25/24 Remote LED indicator 24 VDC Direct two-wire connection to detector



Flashing option


High luminosity





Shock resistant

Remote LED indicator 24 VDC PA25/24


62/105

FIRE SOUNDERS & BEACONS


63/105

Page 62

Fire Sounders & Beacons

A compact high output, low current sounder ideal for hotels and hospitals.Available in panel mount, flange mount, and cover flange.


AS262 Compact sounder

AS262FL Mini sounder, flange mount

AS262COF Mini sounder, cover flange mount


High sound output

12 - 24 V dc and 230 Vac

Available in panel and flange mount

Compact sounder AS262


64/105

Page 63


Technical Data

Operation Continuous


Current consumption 7 mA

(see tone table in manual)

Number of tones 26

Starting current 30 mA, 2 msec

Automatic synchronisation Phased start

Line monitoring input Polarised input

Housing ABS plastic

Lens -Ingress protection IP 65

Operating temperature -25 to +80 C

Dimensions in mm ( x D)

Shallow base 93 x 75

Deep base 93 x 105


AS263 Sounder, 26 tones - shallow base

AS263IS AS 263 intrinsically safe, weatherproof sounder

AS263WAT AS 263 , wh ite w ith ant i-tamper

AS263HIS High output in trinsic safe sounder


High sound output

Multiple tones selection

12 - 24 V dc and 230 Vac

Automatic synchronisation

Suitable for multiple stage evacuation

Red and white colour body

IP 65 intrinsic safe and high output ; IP 66/67 intrinsic safeversions

Low profile version

Version with xenon flash

Red or clear lens for beacon

Sounder, 26 tones - shallow base AS263


65/105

Page 64


Technical Data




(see tone table in manual) @ 240V

Number of tones 26

Starting current 30 mA 30 mA - 2 ms



Housing ABS plastic

Ingress protection IP 65Operating temperature -25 to +80 C

Dimension ( x D)

Shallow base 93 x 75 mm

Deep base 93 x 105 mm


AS264 Sounder, 26 tones - deep base

AS264M AS 264 mains powered 230 VAC


High sound output


12 - 24 V dc and 230 Vac





Low profile version



Sounder, 26 tones - deep base AS264


66/105

Page 65


Technical Data





Number of tones 2

Starting current 30 mA - 10 ms



Housing ABS plastic

Lens PolycarbonateIngress protection IP 65

Operating temperature -10C to +55 C

Dimensions in mm ( x D)

Shallow base 93 x 92

Deep base 93 x 121


AS266 Combined sounder and beacon, 2 tones, red lens - shallow base

AS267 Combined sounder and beacon , 2 tones, red lens - deep base


High sound output


12 - 24 V dc and 230 Vac





Low profile version



Combined sounder and beacon, 2 tones, red lens - shallow base AS266


67/105

Page 66


Technical Data




Number of tones 4

Starting current -



Housing ABS plastic

Lens -

Ingress protection IP 42Operating temperature 25C to +85 C

Dimensions in mm ( x D) 101 x 25


AS268 Sounder, 4 tones, low profile - low current


High sound output




Low profile version

Sounder, 4 tones, low profile - low current AS268


68/105

Page 67


Technical Data





Number of tones 3

Starting current -



Housing ABS plastic

Lens -Ingress protection IP 42

Operating temperature -25C to+70 C


AS269 Sounder, 3 tones - low current, high output


High sound output




Sounder, 3 tones - low current, high output AS269


AF310 Electronic solenoid bell, 24 VDC, red

Electronic solenoid bell, 24 VDC, red AF310


69/105

Page 68


The SK06 cylindrical siren is available in various colours and is designed foruse inside buildings. Its compactness enables easy integration with building

interiors.

Tones are chosen by selection of micro switches. The siren clips onto a base

whereafter a saftey clip prevents unauthorised removal of the sounder from its

base. As an option, a deep base allows for cable entry and tubes up to a

diameter of 22 mm.

Technical Data


Supply Voltage 24 VDC

Current Consumption 12 to 17 mA

Environmental

Operating Temperature -40C + 70C

Ingress Protection IP45

Operational Parameters

Sounds ZC - FR - FL - SC

Sound Output 68 to 103 dBA

Colours Red, White, Cream


SK06 Electronic alarm siren

Compact

Volume control

Up to 103 dB @ 1m

Very low current consumption

Easy assembly

Four different tones

No maintenance

Various colours

Bottom and sides cable entries

IP45

Electronic alarm siren SK06


70/105

Page 69


The SK07 multi-tone siren is designed to sound an acoustic alarm signalinside buildings. This small, low profile siren combines a loud sound with low

power consumption. It complies with the requirements of the EN 54-3

standard.

Technical Data

Electrical

Supply Voltage 22 - 26 VDC

Alarm current 3 mA at 85 dBA or less than 20 mA at 95 dBA

Maximum sound level 95 dBA

Working temperature -20 C to 50 C

Storage temperature -20 C to 70 C

Maximum relative humidity 95 % (non condencing)

Mechanical

Dimensions 63 mm (h) x 93 mm Protection Index IP445

Fastening screws 2 x 30 mm

Maximum cable section 2.5 mm

Recommended cable s ize Sing le co re 1 .5 mm


SK07 Low consumption multi-tone alarm siren

Low profile

Easy installation

Back and side cable entry

Polarity sensitive

Connection base included

Input and output terminals included

Acoustic power output selection

Up to 95 dBA sound output

Eight different alarm tones

Automatic tone change


Low maintenance


EN54 part 3 compliant

Low consumption multi-tone alarm siren SK07


71/105

Page 70


The SK20 is a general purpose sounder designed as part of a fire detectionsystem. For a fire system to fully comply with the provisions set forth in the

regulations for fire fighting installations, following the installation

recommendations of the UNE23-007-14 standard is advised.

Technical Data

Electrical Requirements

Supply voltage 9 to 30 VDC

Consumption @ 24 (tone dependant) 7 to 30 mA

Acoustic power output (tone dependant) 87 to 112 dBA

Nominal power of strobe 1 W

Environmental Specification



Relative humidity < 95%Protection level IP445

Functional Specification

Strobe frequency 60 flashes/minute

Colour Red RAL3001

Size ( h x ) 80 x 92 mm

Weight 180 g


SK20 Alarm sounder with beacon

32 different tones

Includes flashing beacon

Low profile

Very low consumption

Up to 112 dBA sound output levels


Sound output power selection

Input and output terminals provided

Easy installation

Low maintenance

Back and side cable entry


Alarm sounder with beacon SK20


72/105

Page 71


The SK40 alarm siren with luminous indicator has been designed specificallyfor external use. Its main function is to warn people outside a building of the

detection of a fire alarm inside the building. The SK40 combines the acoustic

and indicator parts in a single housing, and is activated with a single voltage

input.

Technical Data



Alarm Current @ 24V 220 mA


Ingress Protection IP33

Operating Temperature -20 to 60 C

Storage Temperature -20 to 60 CPhysical Characteristics

Dimentions (h x w x d) 297 x 210 x 75 mm

Sound Output 105 dB at 1 m

Sound Frequency 2.8 to 3.1 kHz 3%

Cycle Time 1 min ON 1 min OFF

Flash Rate 1 flash /s


SK40 Alarm sounder with indicator

High sound output

Exterior operation

Sectable activation times

Optional battery backup

Optional line supervision

Alarm sounder with indicator SK40


73/105

Page 72


The PA40 Xenon Strobe has been designed for in and outdoor use. It isavailable with various colour lenses to suit the application.

Technical Data


Supply Voltage 12/24 VDC

Current Consumption (12 VDC) 115 mA 20 %

Current Consumption (12 VDC) 35 mA 25 %


Operating Temperature -20 C to +60 C

Operational Specifications

Flash rate 60-100 flashes/min @ 20C

Operating life 200 hours

Colours Amber, blue, clear, red

Dimentions ( h x ) 79 x 90 mm


PA40 Xenon strobe light High intensity xenon

12 and 14 VDC operation


Low maintenance

Xenon strobe light PA40

The CK406 electronic fire alarm bell is designed as an acoustic fire

annunciator. Thanks to their small dimensions and overall design, they are

ideal to install in-doors. The CK406 works with 24 VDC supply and the

advantage of having very low current consumption (less than 30 mA). This

makes them compatible with all good fire alarm systems on the market.

Technical Data


Supply Voltage 24 VDC


Physical Characteristics

Sound Output 95 dB/mColour Red

Weight 0.9 kg

Diameter 6 (150 mm)


CK406 Fire alarm bell


Suitable for indoor use

Easy Installation

24 VDC powered Very reliable

Low maintenance

Fire alarm bell CK406


74/105

ELECTROMAGNETIC DOOR HOLDERS


75/105

Page 74

Electromagnetic door holders

Technical Data

Volt 24

Power 1.6

Holding force (daN) 40

IP rating 42

Dimensions (mm) 70 x 85 x 40

Keeper plate flat/swivel S

Release button -

Protection diode -

Reverse polarity -

Cable entry 2EN1155 Yes

NF61937 -

BS5839pt3 -


FE831 Door holder, steel box, surface mount, basic Complete range for wall and surface mount

Low power - 1,6 W

40 daN holding power standard series

70 daN holding power on VDS coils

100% duty cycle

Anti-remnant ejector

Protection diode and reverse polarity protection on mostmodels

Release button on most models

EN and French approvals (see specification)

Door holder, steel box, surface mount, basic FE831


76/105

Page 75


Technical Data

Volt 24

Power 1.6


IP rating 42



Release button Yes

Protection diode Yes

Reverse polarity -


NF61937 Yes

BS5839pt3 Yes


FE832 Door holder, steel box, surface mount complete Complete range for wall and surface mount

Low power - 1,6 W



100% duty cycle





Door holder, steel box, surface mount complete FE832


77/105

Page 76


Technical Data

Volt 24

Power 1.6


IP rating 30


Keeper plate flat/swivel F

Release button -

Protection diode -

Reverse polarity -

Cable entry -EN1155 Yes

NF61937 -

BS5839pt3 -


FE835 Door holder, steel square base Complete range for wall and surface mount

Low power - 1,6 W



100% duty cycle





Door holder, steel square base FE835


78/105

Page 77


Technical Data

Volt 24

Power 1.6


IP rating 30



Release button -


Reverse polarity Yes


VDS Coil Yes


FE835VDS Door holder, steel square base, VDS magnet

Complete range for wall and surface mount

Low power - 1,6 W



100% duty cycle





Door holder, steel square base, VDS magnet FE835VDS


79/105

Page 78


Technical Data

Volt 24

Power 1.6


IP rating 42



Release button Yes




NF61937 Yes

BS5839pt3 Yes


FE836 Door holder, flush mounting Complete range for wall and surface mount

Low power - 1,6 W



100% duty cycle





Door holder, flush mounting FE836


80/105

Page 79


Technical Data

Volt 24

Power 1.6


IP rating 42



Release button Yes




NF61937 Yes

BS5839pt3 Yes


FE841 Door holder, reinforced aluminium box Complete range for wall and surface mount

Low power - 1,6 W



100% duty cycle





Door holder, reinforced aluminium box FE841


81/105

Page 80


Technical Data

Volt 24

Power 1.6


IP rating 52



Release button Yes




VDS Coil Yes


FE841VDS Door holder, reinforced plastic box, VDS magnet


Low power - 1,6 W



100% duty cycle





Door holder, reinforced plastic box, VDS magnet FE841VDS


82/105

Page 81


Technical Data

Volt 24

Power 1.6


IP rating 42



Release button Yes


Reverse polarity -

Cable entry -

EN1155 Yes

NF61937 Yes

BS5839pt3 Yes


FE845 Door ho lde r, wa ll mount, rein forced a luminium box Complete range for wall and surface mount

Low power - 1,6 W



100% duty cycle





Door holder, wall mount, reinforced aluminium box FE845

Technical Data



FE845-40 Reinforced aluminium extension for FE845, 40mm

Reinforced aluminium extension for FE845, 40mm FE845-40


83/105

Page 82


Technical Data





Technical Data






84/105

Page 83


Technical Data

Volt 24

Power 3


IP rating 42



Release button Yes


Reverse polarity -


NF61937 Yes

BS5839pt3 Yes


FE848 Door ho lde r, fl oor mounting, re in forced aluminium box


Low power - 1,6 W



100% duty cycle





Door holder, floor mounting, reinforced aluminium box FE848


85/105

Page 84


Technical Data

Volt 24

Power 1.6


IP rating 42

Dimensions (mm) -


Release button Yes



Cable entry -

EN1155 Yes

VDS Coil Yes


FE851VDS Door holder, universal adjustable tube, 175mm, VDS magnet


Low power - 1,6 W



100% duty cycle





Door holder, universal adjustable tube, 175mm, VDS magnet FE851VDS

Technical Data

Volt 24

Power 1.6


IP rating 42

Dimensions (mm) -


Release button Yes



Cable entry -

EN1155 Yes

VDS Coil Yes


FE852VDS Door holder, universal adjustable tube, 475mm, VDS magnet


Low power - 1,6 W



100% duty cycle





Door holder, universal adjustable tube, 475mm, VDS magnet FE852VDS


86/105

Page 85


Technical Data

Volt 24

Power 1.6


IP rating 65

Dimensions (mm) -


Release button -



Cable entry 1

EN1155 Yes

VDS Coil Yes


FE855VDS Door holder, steel square base, IP65, VDS magnet

Complete range for wall and surface mount Low power - 1,6 W



100% duty cycle




EN and Fr

Door holder, steel square base, IP65, VDS magnet FE855VDS


87/105

Page 86


Technical Data

Volt 24

Power 1.6


IP rating Ex

EN1155 ATEX


FE858EX Door holder, explosion proof


Low power - 1,6 W

50 daN holding power

100% duty cycle


EX version

Explosion proof, ATEX approval

Door holder, explosion proof FE858EX


88/105

TEST AND SERVICE EQUIPMENT


89/105

Page 88

Test and Service Equipment


FG010 Universal detector removal too l on a swing f rame

ET010 Fibreglass telescopic pole 1.26 m - 4.5 m

ET011 F ib reg lass ex tension tube 1 .2 m (maximum 3 per ET010)

Universal removal tool on swing frame

- size adjustable to fit most detectors

- quick & easy removal of detectors Lightweight telescopic poles

- fibreglass

- non conductive

- use with tools up to 9m

Canvas carry bag

- easy transport of the equipment

Universal detector removal tool on a swing frame FG010


90/105

Page 89



TR010 Touch sensitive transparent dispenser cup on swing frame



SC008 Test Spray for Smoke Detectors

Smoke aerosol dispenser

- universal, touch sensitive

Lightweight telescopic poles

- fibreglass

- non conductive


Ozone friendly test aerosol

- tests ionisation and optical sensors

- faster response and clearing times

Canvas carry bag


Touch sensitive transparent dispenser cup on swing frame TR010


91/105

Page 90



TH010 Mains operated heat detector test tool on swing frame



Heat detector tester

- 230V mains version


- fibreglass

- non conductive


Canvas carry bag


Mains operated heat detector test tool on swing frame TH010


92/105

Page 91


This state-of-the-art heat detector utilises cross-flow technology for fast,efficient heat detector testing. The battery pack is contained within the test

pole


TH012 Cordless, bat ter y operated , heat de tec tor on swing frame

CB001 Canvas carry ing bag for the test and service equ ipment

Heat detector testers

- battery operated


- fibreglass

- non conductive


- faster response and clearing times

Canvas carry bag


Cordless, battery operated, heat detector on swing frame TH012


93/105

Page 92






- fibreglass

- non conductive


Canvas carry bag


Fibreglass telescopic pole 1.26 m - 4.5 m ET010

Technical Data

According to material safety data sheet


SC008 Test Spray for Smoke Detectors

No damage to detector plastics and components

Faster response tim

catalog accesorii incendiu

Documents